2. THROTTLE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
_r.._IYI'ION:3 | Do | not | kink | the | throttle | cable |
| i |
|
|
|
| ARM | ||||||||
a: | SlideFoamtheThrottleGrip. Trigger | Housing | away from | the | . | ,_ |
| _1 | .... | ||||||||||||
| 'NOTE: | Before | performing | step "b", push the barrel |
| _ |
| 0'__ |
|
|
| ||||||||||
| _the |
| throttle | cable | into | the | sheath until | the |
|
| _ | ] | [,,I,_q¢ |
| |||||||
| barrel | contacts | the | sheath. |
|
|
|
|
|
| ' |
| ! |
| _.._'€_ | I | \, |
| |||
b | Insert | the | Throttle |
| Cable | through |
| the tunnel | in | _he |
| no, rsnno'_ | Jl |
| \ | ||||||
| Foam | Grip until | the end | of | the | Cable | extends | at |
| ...... | N: .... | ],], aAu_n_ | |||||||||
| least 2 inches beyond :the | Grip. |
|
|
|
|
|
| TRIGGER | j ], I | _I_O'F" | ||||||||||
c. | Hold the | Trigger | away from | the Drive | Shaft | Hous- |
|
|
| _._ | C._LZ | ||||||||||
| ing and insert | the | barrel | end | of | the Throttle | Cable |
| , |
|
|
into the round_ opening in the Trigger._. |
| |
inserting the barre! end | Nut | |
|
|
Throttle Cable into the round opening in the Trigger, make sure that the barrel is completely inserted and the Throttle Cable is located in 'the split in the Arm.
d. Push the Trigger back into the Housing while guid -
ing the Cable through the split in the art 9. Guide_ the arm into the Foam Grip tunnel while replacing, the Throttle Trigger Housing trash againstthe Grip__
e. Hold Trigger_against the Foam Grip while
[CAUTION: ('Do
3. HANDLEBAR•
alXWARNING
The handlebar mountingblock must be placed above the point of the arrow on the safety labels. The handlebar is a barrier to keep the blade away from the operator's feet.
a. Position either side of the mounting block on the drive shaft Housing above the arrow on the Safety Labels.
b. Place one of the covers below the drive shaft Hous-
ing and secure it to the mounting block with 2
c. | Align | the | Handlebar | with | the straight barrier | por- |
| |||
| tion to the left and the curved portion to the right. _ |
| ||||||||
d. Position the Mounting Block between the arrows |
| |||||||||
| on the short, straight section of the Handlebar. |
| ||||||||
e. Place | the | remaining | Cover | over the | Handlebar | and |
| |||
| secur e it | with two_re__WSs_iC_":,finger tightenordy.- | [ . | |||||||
f. | Be | sure | the | Handlebar is | installed | correctly, | then | SAFETY | ||
.... | tighten | each | screw securely | with a wrench. |
| LABELS | ||||
| / | |||||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| AWMUIDI0 |
|
|
| ||
The long, straight portion of the Handlebar must be |
| |||||||||
installed to provide a barrier between the operator |
| |||||||||
and | the | spinning | blade. |
|
|
|
|
|
:C
CABLE