Remove top two bolts that secure auger housing to motor mount frame. Loosen bottom two botts, Auger housing and motor mount frame willseparate, hinged by bottom two bolts.

Remove old bell from auger drive pulley.

Install the original equipment replacement belt in reverse order of removal.

Position drive belt onto the auger ddve pulley.

Adjust the belt guide (see To Adjust The Belt Guide paragraph).

Reinstall the belt cover.

NOTE: You may have to move the auger idler pulley more than once to obtain the cor- rect tension.

Check the clutch control cable adjustment.

Reconnect the spark plug wire.

TRACTION DRIVE BELT

If your snow thrower will not move forward, check the traction ddve belt (see second

figure on page 19) for wear (Check other causes also in the Trouble Shooting Points section). Ifthe traction drive belt needs to be replaced, proceed as follows:

Disconnect the spark plug wire.

Remove the belt cover (see second fig- ura).

Loosen the belt guide and pull away from auger drive pulley (see second figure on page 19).

Remove auger drive belt from auger pul- ley (see second figure on page 19).

Pull the traction ddve belt idler pulley away from the traction drive belt (see second figure on page 19).

Remove the traction ddve belt.

Position new traction ddve belt onto trac- tion pulley.

Pull idler pulley away from belt, allowing beltto be positioned onto auger pulley.

Check clutch control cable adjustment, see page

Reconnect the spark plug wire.

TO ADJUSTTHE BELT GUIDE

Disconnect the spark plug wire.

Remove the belt cover (see third figure on page 19).

Engage the auger drive clutch lever.

Measure the distance between the belt

guide and the belt (see figure below). The distance should be 1/8".

If adjustment is necessary, loosen the belt guide mounting bolt. Move the belt guide to the correct position and tighten the mounting bolt.

Reinstall the belt cover.

Reconnect the spark plug wire.

.("_X_ Drive Pulley

Auger Idler--_

_Impeller

TO ADJUST THE FRICTION WHEEL

If the snow thrower will not move forward,

you need to check the traction drive belt, the traction ddve cable or the friction wheel, if the friction wheel is damaged, it will need to be replaced (see the To Replace Friction Wheel paragraph on page 21). If the friction wheel is not worn, check the adjustment, as follows:

Disconnect the spark plug wire.

Drain the gasoline from the gas tank.

Stand snow thrower on the auger housing end.

Remove the bottom panel (see figure be- low).

Remove Bolts

 

_Bo_om

Pane

Remove

 

 

To0

 

 

(Each "_'_"

 

Side)

bottombol_

Looser_

(Bo_om View)

 

'(each side)

Position the shifter lever in first (1) for- ward gear.

Note the position of the friction wheel on the disc drive plate.Proper position from

the right outer side of disc drive plate to the center of friction wheel should be 3"

(76 mm) (see next figure).

20

Page 20
Image 20
Craftsman 536.88123 operating instructions To Adjustthe Belt Guide, To Adjust the Friction Wheel

536.88123 specifications

The Craftsman 536.88123 is a powerful and versatile snow blower designed to tackle the toughest winter weather conditions. With its robust construction and advanced features, this machine is engineered for homeowners who desire efficiency and reliability in snow removal.

One of the standout features of the Craftsman 536.88123 is its impressive 27-inch clearing width. This wide path allows users to cover large areas quickly, making it suitable for both residential driveways and sidewalks. The snow blower is equipped with a strong and efficient 2-stage auger system that not only breaks up compact snow but also throws it far away from the cleared area. This ensures that snow is efficiently removed without simply pushing it aside, which can cause buildup over time.

Another significant characteristic of this model is its powerful 357cc engine, delivering substantial torque and performance. This engine is designed to handle heavy, wet snow with ease, providing users with the confidence to tackle even the most challenging conditions. The electric start feature adds convenience for those cold, winter mornings, allowing for easy ignition without the need for strenuous pulling.

The Craftsman 536.88123 is also designed for user comfort and ease of operation. The adjustable handle ensures a comfortable grip, and it can be modified to fit the user’s height. This snow blower features six forward and two reverse speeds, giving users full control over their snow clearing experience. The durable, rubber-edged auger not only provides efficient snow removal but also protects surfaces underneath, minimizing the risk of damage.

Additionally, the snow blower comes with a remote chute control system, allowing users to easily direct the snow discharge without having to manually adjust the chute. This feature is particularly beneficial for users who need to navigate around obstacles while working.

In terms of durability, the Craftsman 536.88123 is built with high-quality materials designed to withstand harsh conditions, ensuring longevity and dependable performance year after year.

With its combination of power, efficiency, and user-friendly design, the Craftsman 536.88123 is a top choice for those looking for a reliable solution to winter snow challenges. Whether you're clearing your driveway, sidewalk, or patio, this snow blower promises to make your winter maintenance tasks manageable and less labor-intensive.