TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be necessary, check adjustment as de- scribed below before loosening cable. If adjustment is necessary, proceed as follows:

1.With engine not running, move choke control (located on dash panel) to full choke position.

2.Remove air cleaner cover, filter and cartridge plate to expose carburetor choke (See "AIR FILTER" in the

Maintenance section of this manual).

3.Choke should be closed. If it is not,

loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

4.Reassemble air cleaner.

Closed for Full

TO ADJUST CARBURETOR

The carburetor has been present at the factory and adjustment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture. Turning the adjusting needles out (countemlockwise) increases the supply

of fuel to the engine giving a richer fuel/ air mixture.

IMPORTANT: Damage to the needles and the s_ats in carburetor may result if screw is turned in too tight.

PRELIMINARY SE'I-rlNG -

1.Be sure you have a clean air filter, and the throttle control cable is adjusted properly (see "TO ADJUST

THRO'I-rLE CONTROL CABLE" in the

Service and Adjustments section of this manual).

2.With engine off tum idle fuel adjusting needle In (clockwise) closing it finger tight and then turn out (counterclock- wise) 1 turn.

FINAL SETTING -

1.Start engine and allow to warm for five minutes. Make final adjustments with engine running and shift/motion control lever in neutral (N) position.

NOTE: The high idle is set at the factory and cannot be adjusted.

2.Idle soeed setting - With throttle control lever in slow position, engine should idle at 1200 RPM. If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is attained.

3.Idle fuel needle setting - With throttle control lever in slow position, turn idle fuel adjusting needle in (clockwise) until engine speed decreases and then turn out (countemlockwise) approximately 3/4 turn to obtain the best low speed performance.

4.Recheck idle speed. Readjust if necessary.

ACCELERATION TEST-

5.Move throttle control lever from slow to

fast position. If engine hesitates or dies, turn idle fuel adjusting needle out (counterclockwise) 1/8 turn.

Repeat test and continue to adjust, if

necessary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust-damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact Sears or otherqualified servicecenter, which has proper equip- ment and experience to make any necessary adjustments.

27

Page 26 Page 28
Page 27
Image 27
Craftsman 917.274953 manual To Adjust Choke Control, To Adjust Carburetor, Final Setting, Acceleration Test
Page 26 Page 28

917.274953 specifications

The Craftsman 917.274953 is a powerful and versatile lawn mower that has gained popularity among homeowners and landscaping enthusiasts. Known for its reliability and performance, this mower is designed to handle a variety of lawn sizes and types, making it an excellent choice for maintaining a beautifully manicured outdoor space.

One of the standout features of the Craftsman 917.274953 is its robust engine. Equipped with a 42-inch cutting deck, the mower is powered by a reliable Briggs & Stratton engine. This engine delivers sufficient power to tackle thick grass and uneven terrain with ease. The self-propelled drive system allows users to effortlessly maneuver the mower across their lawns, reducing fatigue and making the mowing process more efficient.

Another notable characteristic of this mower is its adjustable cutting height. With multiple height settings, users can easily customize the length of their grass to achieve their desired lawn appearance. This flexibility is particularly useful during different growing seasons, allowing users to adapt to changing grass conditions.

In terms of technology, the Craftsman 917.274953 incorporates innovative features that enhance its usability. The mower is designed with a rear bagging system, which efficiently collects clippings, leaving a clean finish after mowing. For those who prefer mulching, the mower also includes a mulching option that allows grass clippings to be finely chopped and returned to the soil, providing natural nutrients.

Additionally, the Craftsman mower boasts a durable construction, featuring a robust steel deck that ensures longevity and resistance to wear and tear. This quality construction not only extends the mower's lifespan but also enhances its performance in various weather conditions.

The ergonomic design of the mower offers user comfort, with an adjustable handle that accommodates different heights. This attention to comfort minimizes strain during extended use, making it suitable for homeowners with larger properties.

Overall, the Craftsman 917.274953 lawn mower combines powerful performance, user-friendly features, and durable construction, making it an excellent choice for those seeking to maintain a healthy and attractive lawn. Whether you have a small backyard or a larger landscape, this mower can adapt to your needs, making lawn care a more manageable and enjoyable task.
Top Page Image Contents