Cypress CY7C1319CV18, CY7C1321CV18 manual Maximum Ratings, DC Electrical Characteristics

CY7C1317CV18, CY7C1917CV18 CY7C1319CV18, CY7C1321CV18

Maximum Ratings

Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested.

Storage Temperature ................................. –65°C to +150°C

Ambient Temperature with Power Applied.. –55°C to +125°C

Supply Voltage on VDD Relative to GND		–0.5V to +2.9V
Supply Voltage on VDDQ Relative to GND		–0.5V to +VDD
DC Applied to Outputs in High-Z	–0.5V to VDDQ + 0.3V
DC Input Voltage [11]	–0.5V to V + 0.3V
		DD

Current into Outputs (LOW)			20 mA
Static Discharge Voltage (MIL-STD-883, M 3015)....			>2001V
Latch up Current	.....................................................		>200 mA
Operating Range
	Ambient	VDD [15]	VDDQ [15]
Range	Temperature (TA)
Commercial	0°C to +70°C	1.8 ± 0.1V	1.4V to
			VDD
Industrial	–40°C to +85°C

Electrical Characteristics

DC Electrical Characteristics

Over the Operating Range [12]

Parameter	Description	Test Conditions			Min	Typ	Max	Unit
VDD	Power Supply Voltage				1.7	1.8	1.9	V
VDDQ	IO Supply Voltage				1.4	1.5	VDD	V
VOH	Output HIGH Voltage	Note 16			VDDQ/2 – 0.12		VDDQ/2 + 0.12	V
VOL	Output LOW Voltage	Note 17			VDDQ/2 – 0.12		VDDQ/2 + 0.12	V
VOH(LOW)	Output HIGH Voltage	IOH = −0.1 mA, Nominal Impedance			VDDQ – 0.2		VDDQ	V
VOL(LOW)	Output LOW Voltage	IOL = 0.1 mA, Nominal Impedance			VSS		0.2	V
VIH	Input HIGH Voltage				VREF + 0.1		VDDQ + 0.3	V
VIL	Input LOW Voltage				–0.3		VREF – 0.1	V
IX	Input Leakage Current	GND ≤ VI ≤ VDDQ			−5		5	μA
IOZ	Output Leakage Current	GND ≤ VI ≤ VDDQ, Output Disabled			−5		5	μA
VREF	Input Reference Voltage [18]	Typical Value = 0.75V			0.68	0.75	0.95	V
IDD [19]	VDD Operating Supply	VDD = Max,	300 MHz	(x8)			770	mA
		IOUT = 0 mA,
				(x9)			770
		f = fMAX = 1/tCYC
				(x18)			810
				(x36)			890
			278 MHz	(x8)			720	mA
				(x9)			720
				(x18)			760
				(x36)			830
			250 MHz	(x8)			670	mA
				(x9)			670
				(x18)			700
				(x36)			765

Notes

15.Power up: assumes a linear ramp from 0V to VDD(min) within 200 ms. During this time VIH < VDD and VDDQ < VDD.

16.Outputs are impedance controlled. IOH = –(VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.

17.Outputs are impedance controlled. IOL = (VDDQ/2)/(RQ/5) for values of 175Ω < RQ < 350Ω.

18.VREF(min) = 0.68V or 0.46VDDQ, whichever is larger, VREF(max) = 0.95V or 0.54VDDQ, whichever is smaller.

19.The operation current is calculated with 50% read cycle and 50% write cycle.

Document Number: 001-07161 Rev. *D Page 21 of 31

[+] Feedback