Cypress CY7C2576KV18, CY7C2563KV18, CY7C2561KV18 manual Pin Definitions Pin Name Pin Description

PRELIMINARY

CY7C2561KV18, CY7C2576KV18

CY7C2563KV18, CY7C2565KV18

Table 2. Pin Definitions

Pin Name

IO

Pin Description

D[x:0]

Input-

Data Input Signals. Sampled on the rising edge of K and

clocks when valid write operations are active.

K

Synchronous

CY7C2561KV18 − D[7:0]

CY7C2576KV18 − D[8:0]

CY7C2563KV18 − D[17:0]

CY7C2565KV18 − D[35:0]

Input-

Write Port Select − Active LOW. Sampled on the rising edge of the K clock. When asserted active, a

WPS

Synchronous

write operation is initiated. Deasserting deselects the write port. Deselecting the write port ignores D[x:0].

0,

Input-

Nibble Write Select 0, 1 − Active LOW (CY7C2561KV18 Only). Sampled on the rising edge of the K

NWS

NWS1,

Synchronous

and K clocks when write operations are active. Used to select which nibble

is written into the device

during the current portion of the write operations. NWS0 controls D[3:0] and NWS1 controls D[7:4].

All the Nibble Write Selects are sampled on the same edge as the data. Deselecting a Nibble Write Select

ignores the corresponding nibble of data and it is not written into the device.

0,

Input-

Byte Write Select 0, 1, 2 and 3 − Active LOW. Sampled on the rising edge of the K and

clocks when

BWS

K

BWS1,

Synchronous

write operations are active. Used to select which byte is written into the device during the current portion

BWS2,

of the write operations. Bytes not written remain unaltered.

BWS3

CY7C2576KV18 − BWS0

controls D[8:0]

CY7C2563KV18 − BWS0

controls D[8:0]

and

BWS

1 controls D[17:9].

CY7C2565KV18 − BWS0

controls D[8:0], BWS1 controls D[17:9],

BWS2 controls D[26:18] and BWS3 controls D[35:27].

All the Byte Write Selects are sampled on the same edge as the data. Deselecting a Byte Write Select

ignores the corresponding byte of data and it is not written into the device.

A

Input-

Address Inputs. Sampled on the rising edge of the K clock during active read and write operations. These

Synchronous

address inputs are multiplexed for both read and write operations. Internally, the device is organized as

8M x 8 (4 arrays each of 2M x 8) for CY7C2561KV18, 8M x 9 (4 arrays each of 2M x 9) for CY7C2576KV18,

4M x 18 (4 arrays each of 1M x 18) for CY7C2563KV18 and 2M x 36 (4 arrays each of 512K x 36) for

CY7C2565KV18. Therefore, only 21 address inputs are needed to access the entire memory array of

CY7C2561KV18 and CY7C2576KV18, 20 address inputs for CY7C2563KV18 and 19 address inputs for

CY7C2565KV18. These inputs are ignored when the appropriate port is deselected.

Q[x:0]

Outputs-

Data Output Signals. These pins drive out the requested data when the read operation is active. Valid

Synchronous

data is driven out on the rising edge of the K and K clocks during read operations. On deselecting the

read port, Q[x:0] are automatically tri-stated.

CY7C2561KV18 − Q[7:0]

CY7C2576KV18 − Q[8:0]

CY7C2563KV18 − Q[17:0]

CY7C2565KV18 − Q[35:0]

Input-

Read Port Select − Active LOW. Sampled on the rising edge of positive input clock (K). When active, a

RPS

Synchronous

read operation is initiated. Deasserting deselects the read port. When deselected, the pending access is

allowed to complete and the output drivers are automatically tri-stated following the next rising edge of

the K clock. Each read access consists of a burst of four sequential transfers.

QVLD

Valid output

Valid Output Indicator. The Q Valid indicates valid output data. QVLD is edge aligned with CQ and

CQ.

indicator

ODT [3]

On-Die

On-Die Termination Input. This pin is used for On-Die termination of the input signals. ODT range

Termination

selection is made during power up initialization. A LOW on this pin selects a low range that follows RQ/3.33

input pin

for 175Ω < RQ < 350Ω (where RQ is the resistor tied to ZQ pin). A HIGH on this pin selects a high range

that follows RQ/1.66 for 175Ω < RQ < 250Ω (where RQ is the resistor tied to ZQ pin). When left floating,

a high range termination value is selected by default.

Note

3. On-Die Termination (ODT) feature is supported for D[x:0], BWS[x:0], and K/K inputs.

Document Number: 001-15887 Rev. *E Page 6 of 29

[+] Feedback