Manuals / D-Link / Computer Equipment / Network Cables

D-Link DFL-200 Remote Net 192.168.1.0/24, Enable Automatically add a route for the remote network

Models: DFL-200

1 133

Download 133 pages 54.3 Kb

Page 80

PSK: 1234567890 (Note! You should use a key that is hard to guess)

Retype PSK: 1234567890

Select Tunnel type: LAN-to-LAN tunnel

Remote Net: 192.168.1.0/24

Remote Gateway: 194.0.2.20

Enable Automatically add a route for the remote network

Click Apply

3.Setup policies for the new tunnel, Firewall->Policy:Click Global policy parameters

Enable Allow all VPN traffic: internal->VPN, VPN->internal and VPN->VPN Click Apply

80

Image 80

D-Link DFL-200 manual Remote Net 192.168.1.0/24, Enable Automatically add a route for the remote network

Contents

Link DFL-200 Contents VPN Servers 111 122 125Features and Benefits Access Control supportedIntroduction Introduction to FirewallsIntroduction to Local Area Networking LEDs Physical ConnectionsPackage Contents System RequirementsResetting the DFL-200 Managing D-Link DFL-200Administration Settings Administrative AccessAdd ping access to an interface Add Admin access to an interfaceAdd Read-only access to an interface Enable Snmp access to an interfaceChange IP of the LAN or DMZ interface SystemInterfaces IP Address The IP address of the WAN interface. This is WAN Interface Settings Using Static IPWAN Interface Settings Using Dhcp WAN Interface Settings Using PPPoE PasswordWAN Interface Settings Using Pptp Password The password supplied to you by your ISP WAN Interface Settings Using BigPondMTU Configuration Routing Go to System and Routing Add a new Static RouteRemove a Static Route Logging Enable E-mail alerting for ISD/IDP events Enable LoggingEnable Audit Logging Page Time Using NTP to sync time Setting time and date manuallyChanging time zone Checking the Set the system time boxFirewall PolicyPolicy modes Action TypesSchedule Service FilterSource and Destination Filter Intrusion Detection / Prevention Add a new policyConfigure Intrusion Detection Enable the Delete policy checkboxEnable the Intrusion Detection / Prevention checkbox Change order of policyConfigure Intrusion Prevention Port mapping / Virtual Servers Add a new mappingEnable the Delete mapping checkbox Delete mappingUsers DFL-200 Radius SupportEnable User Authentication via Http / Https Enable Radius SupportAdd User Change User PasswordEnable the Change password checkbox Enable the Delete user checkbox Delete UserSchedules Add new recurring scheduleServices Adding TCP, UDP or TCP/UDP ServiceGrouping Services Adding IP ProtocolProtocol-independent settings VPN Introduction to IPSecPoint-to-Point Protocol Introduction to PptpIntroduction to L2TP Authentication Protocols MPPE, Microsoft Point-To-Point EncryptionAuthentication protocol L2TP/PPTP ClientsAuthentication Protocol Introduction chapter L2TP/PPTP ServersMppe encryption VPN between two networks Creating a LAN-to-LAN IPSec VPN TunnelVPN between client and an internal network Creating a Roaming Users IPSec VPN TunnelAdding a L2TP/PPTP VPN Client Adding a L2TP/PPTP VPN ServerVPN Advanced Settings IPSec Proposal List Proposal ListsIKE Proposal List Certificates Trusting CertificatesLocal identities Certificates of remote peersIdentities Content Filtering Active content handlingEdit the URL Global Whitelist Edit the URL Global Blacklist Active content handling Dhcp Server Settings ServersEnable Dhcp Server Enable Dhcp RelayDisable Dhcp Server/Relayer Enable by checking the Use built-in Dhcp Server boxEnable by checking the Enable DNS Relayer box DNS Relayer SettingsEnable DNS Relayer Disable DNS Relayer Tools PingPing Example Add Dynamic DNS SettingsDynamic DNS Restoring the DFL-200’s Configuration BackupExporting the DFL-200’s Configuration Restart/Reset Restarting the DFL-200Restoring system settings to factory defaults Page Upgrade IDS Signature-database UpgradeUpgrade Firmware CPU Load StatusSystem Interfaces VPN Connections Click Connections below it. a window willDhcp Server Logging How to read the logs Usage eventsDrop events Conn eventsOpen Example Close ExampleStep by step guides LAN-to-LAN VPN using IPsec LAN IP 192.168.4.1, Subnet maskEnable Automatically add a route for the remote network Remote Net 192.168.1.0/24LAN IP 192.168.1.1, Subnet mask Local net 192.168.1.0/24Remote Net 192.168.4.0/24 LAN-to-LAN VPN using Pptp Username BranchOffice Click Global policy parameters Settings for Main office Page Select Local database Under Users in local database click Add newPage LAN-to-LAN VPN using L2TP Username BranchOffice Check Use IPsec encryption Setup interfaces, System-Interfaces WAN IP193.0.2.20 Page Select Local database Under Users in local database click Add new More secure LAN-to-LAN VPN solution Page Page Settings for Main office Settings for the Windows XP client Windows XP client and Pptp serverSelect Connect to the network at my workplace and click Next Select Virtual Private Network connection and click Next Name the connection MainOffice and click Next 104 Select Do not dial the initial connection and click Next Page Click Properties Page Name the new user HomeUser Enter password Retype password Page Windows XP client and L2TP server 112 Settings for Main office Page Content filtering Firewall-Services Select HTTP/HTML Content Filtering in the ALG dropdownPage Page Intrusion detection and prevention Page Check Enable E-mail alerting for IDS/IDP events Appendixes Appendix a Icmp Types and CodesPage Appendix B Common IP Protocol Numbers ESPLimited Warranty What Is Not Covered Wichtige Sicherheitshinweise CE Mark Warning WarnungAdvertencia de Marca de la CE AttenzioneVcci Warning Offices Singapore D-LINK International 132