L2TP/PPTP Servers | D-Link DFL-200 instruction

L2TP/PPTP Servers

Name – Specifies a name for this PPTP/L2TP Server.

Outer IP - Specifies the IP that the PPTP/L2TP server should listen on, leave it Blank for the WAN IP.

Inner IP - Specifies the IP inside the tunnel, leave it Blank for the LAN IP.

IP Pool and settings

Client IP Pool - A range, group or network that the PPTP/L2TP Server will use as IP

address pool to give out IP addresses to the clients from.

Primary/Secondary DNS - IP of the primary and secondary DNS servers.

Primary/Secondary WINS - IP of the Windows Internet Name Service (WINS) servers that are used in Microsoft environments which uses the NetBIOS Name Servers (NBNS) to assign IP addresses to NetBIOS names.

Authentication protocol

Specify if, and what authentication protocol to use, read more about the different authentication protocols in the

Authentication Protocol

Introduction chapter.

46

Image 46

D-Link DFL-200 manual L2TP/PPTP Servers, Authentication Protocol Introduction chapter

Contents

Link DFL-200 Contents VPN Servers 111 122 125 Introduction Features and BenefitsAccess Control supported Introduction to Firewalls Introduction to Local Area Networking LEDs Physical Connections Package Contents System Requirements Resetting the DFL-200 Managing D-Link DFL-200 Administration Settings Administrative Access Add ping access to an interface Add Admin access to an interface Add Read-only access to an interface Enable Snmp access to an interface Interfaces SystemChange IP of the LAN or DMZ interface WAN Interface Settings Using Dhcp WAN Interface Settings Using Static IPIP Address The IP address of the WAN interface. This is WAN Interface Settings Using PPPoE Password WAN Interface Settings Using Pptp MTU Configuration WAN Interface Settings Using BigPondPassword The password supplied to you by your ISP Routing Remove a Static Route Add a new Static RouteGo to System and Routing Logging Enable Audit Logging Enable LoggingEnable E-mail alerting for ISD/IDP events Page Time Changing time zone Using NTP to sync timeSetting time and date manually Checking the Set the system time box Policy modes FirewallPolicy Action Types Source and Destination Filter Service FilterSchedule Intrusion Detection / Prevention Add a new policy Enable the Intrusion Detection / Prevention checkbox Configure Intrusion DetectionEnable the Delete policy checkbox Change order of policy Configure Intrusion Prevention Port mapping / Virtual Servers Add a new mapping Enable the Delete mapping checkbox Delete mapping Users DFL-200 Radius Support Enable User Authentication via Http / Https Enable Radius Support Enable the Change password checkbox Change User PasswordAdd User Enable the Delete user checkbox Delete User Schedules Add new recurring schedule Services Adding TCP, UDP or TCP/UDP Service Grouping Services Adding IP Protocol Protocol-independent settings VPN Introduction to IPSec Introduction to L2TP Introduction to PptpPoint-to-Point Protocol Authentication Protocols MPPE, Microsoft Point-To-Point Encryption Authentication protocol L2TP/PPTP Clients Authentication Protocol Introduction chapter L2TP/PPTP Servers Mppe encryption VPN between two networks Creating a LAN-to-LAN IPSec VPN Tunnel VPN between client and an internal network Creating a Roaming Users IPSec VPN Tunnel Adding a L2TP/PPTP VPN Client Adding a L2TP/PPTP VPN Server VPN Advanced Settings IKE Proposal List Proposal ListsIPSec Proposal List Local identities CertificatesTrusting Certificates Certificates of remote peers Identities Content Filtering Active content handling Edit the URL Global Whitelist Edit the URL Global Blacklist Active content handling Dhcp Server Settings Servers Disable Dhcp Server/Relayer Enable Dhcp ServerEnable Dhcp Relay Enable by checking the Use built-in Dhcp Server box Enable DNS Relayer DNS Relayer SettingsEnable by checking the Enable DNS Relayer box Disable DNS Relayer Tools Ping Dynamic DNS Add Dynamic DNS SettingsPing Example Exporting the DFL-200’s Configuration BackupRestoring the DFL-200’s Configuration Restart/Reset Restarting the DFL-200 Restoring system settings to factory defaults Page Upgrade Firmware UpgradeUpgrade IDS Signature-database System StatusCPU Load Interfaces VPN Connections Click Connections below it. a window will Dhcp Server Logging Drop events How to read the logsUsage events Conn events Open Example Close Example Step by step guides LAN-to-LAN VPN using IPsec LAN IP 192.168.4.1, Subnet mask Enable Automatically add a route for the remote network Remote Net 192.168.1.0/24 LAN IP 192.168.1.1, Subnet mask Local net 192.168.1.0/24 Remote Net 192.168.4.0/24 LAN-to-LAN VPN using Pptp Username BranchOffice Click Global policy parameters Settings for Main office Page Select Local database Under Users in local database click Add newPage LAN-to-LAN VPN using L2TP Username BranchOffice Check Use IPsec encryption Setup interfaces, System-Interfaces WAN IP193.0.2.20 Page Select Local database Under Users in local database click Add new More secure LAN-to-LAN VPN solution Page Page Settings for Main office Settings for the Windows XP client Windows XP client and Pptp server Select Connect to the network at my workplace and click Next Select Virtual Private Network connection and click Next Name the connection MainOffice and click Next 104 Select Do not dial the initial connection and click Next Page Click Properties Page Name the new user HomeUser Enter password Retype password Page Windows XP client and L2TP server 112 Settings for Main office Page Content filtering Firewall-Services Select HTTP/HTML Content Filtering in the ALG dropdownPage Page Intrusion detection and prevention Page Check Enable E-mail alerting for IDS/IDP events Appendixes Appendix a Icmp Types and CodesPage Appendix B Common IP Protocol Numbers ESP Limited Warranty What Is Not Covered Wichtige Sicherheitshinweise Advertencia de Marca de la CE CE Mark WarningWarnung Attenzione Vcci Warning Offices Singapore D-LINK International 132