D-Link DRO-210i

High Availability

Dlink DRO-210i User Guide 30

Select Interface →

→→

→ WAN1 and choose IP Setting Mode as Static or Dynamic. Click on

Detect Link Status to configure the Ethernet WAN Link Detection as explained

below.

Ethernet WAN Link Detection

Interface The WAN interface on which link detection is to be performed.

Link Detection Select to enable Link Detection on this Interface.

Mode Select protocol (ARP or ICMP) used to detect reachability of the default

gateway IP address. If the default gateway is reachable, then the Protocol

Status of the Interface will be UP, otherwise it will be DOWN.

No of Retries Enter the number of attempts to reach the default gateway, before

confirming the status (UP/DOWN) of the link.

Delay between

Retries

Enter the time in seconds between retry attempts.

After entering all the information press the Apply button. The Ethernet WAN Status

Table will display the list of interfaces on which Link Detection is enabled and their

status.

Web UI

Contents

Main DRO-210i Broadband Business Gateway User Guide Table Of Contents 3 DHCP, DNS AND TIME.......................................................................... 18 5 HIGH AVAILABILITY............................................................................28 6 NETWORK ADDRESS TRANSLATION...............................................31 8 VIRTUAL PRIVATE NETWORK...........................................................49 9 QUALITY OF SERVICE..........................................................................58 10 ADMINISTRATION...............................................................................63 11 FREQUENTLY ASKED QUESTIONS .................................................70 About This Manual 1 Product Overview 1.1 Hardware Details DRO-210i Package Contents Page Page 1.2 Software Features Routing High Availability Firewall Page Tools Secure Web-based Management 2 Interfaces 2.1 Port Configuration 2.2 LAN Interface 2.3 DMZ Interface 2.4 WAN Interface 2.4.1 Static Mode 2.4.2 Dynamic Mode 2.4.3 PPPoE Mode Page 3 DHCP, DNS and Time 3.1 DHCP 3.1.1 DHCP Server 3.1.2 DHCP Static Mapping 3.1.3 DHCP Relay 3.2 DNS Proxy 3.3 Time 4 Routing 4.1 Static Routing 4.2 Dynamic Routing Page 4.3 Routing Table 4.4 Policy Based Routing Page 5 High Availability 5.1 Auto Backup 5.2 Load Balancing 5.3 Ethernet Link Detection Page 6 Network Address Translation 6.1 NAT 6.1.1 NAT Interface Configuration 6.1.2 NAT Configuration 6.1.3 NAT Exception 6.2 Virtual Server 6.3 SIP-ALG 6.4 NAT Table 7 Firewall 7.1 Firewall Policies 7.1.1 Interface Configuration 7.1.2 Policy Rules 7.1.3 Inbound Policies 7.1.4 Outbound Policies Firewall Dlink DRO-210i User Guide 40 Select Firewall Policy to get to the Policy Table and click Out button to configure Outbound Policies. Page 7.1.5 Domain Filter 7.1.6 Web Filter Page 7.1.7 MAC Filter 7.1.8 Blocking Log 7.2 Intrusion Detection 7.2.1 IDS Configuration Page 7.2.2 Intrusion Log 7.2.3 Black List 8 Virtual Private Network 8.1 IPSec Tunnel or Passthrough 8.2 Peer-To-Peer Page Page 8.3 IPSec Server Page 8.4 Tunnel Table 8.5 IPSec Status 8.6 IPSec Log 9 Quality of Service 9.1 Hierarchical Token Bucket (HTB) 9.1.1 Class Configuration Page 9.1.2 Filter Configuration 9.2 TOS/DiffServ Page 10 Administration 10.1 Device Information 10.2 Traffic Statistics 10.3 Session Log 10.4 SysLog 10.5 Password Change 10.6 System 10.7 Upload/Download 10.8 Ping Test 10.9 Remote Access Page 11 Frequently Asked Questions 11.1 General 11.2 DHCP, DNS 11.3 Routing 11.4 High Availability 11.5 Firewall Page 11.6 NAT 11.7 VPN 11.8 QoS