Datalogic Scanning DS8100A Network Termination

INSTALLATION 2

Network Termination

When building a Lonworks system the network must be properly terminated by positioning

the BTK-8102 Lonworks terminator in the DS8100A master reader and the BTK-8100

Lonworks bus return in the last DS8100A slave reader.

The BTK-8100 bus return provides a connector to be inserted in the Lonworks 17-pin female

connector of the last slave reader in the network; while the BTK-8102 Lonworks terminator

provides a different connector to be inserted in the Lonworks 17-pin male connector of the

master reader:

DS8100A Master DS8100A Last Slave

BTK-8100

BTK-8102

CAB-810X Network CAB-810X

Figure 23 - BTK-8102 and BTK-8100

Two cables are also provided as accessories to terminate and power the network: CAB-8605

and CAB-8305.

CAB-8605 is a power and Lonworks termination cable to be used for connecting the

DS8100A master to an external power unit within the network; while CAB-8305 is a power

and bus return cable to be used for connecting the last DS8100A slave to an external power

unit.

CAB-8605 CAB-8305

DS8100A Master DS8100A Last Slave

Power Unit

Network

Figure 24 – CAB-8605 and CAB-8305

19

Contents

Main Page DS8100A Page CONTENTS Page REFERENCES REFERENCE DOCUMENTATION SERVICES AND SUPPORT COMPLIANCE ELECTRICAL SAFETY LASER SAFETY Standard Regulations POWER SUPPLY WEEE COMPLIANCE GENERAL VIEW DS8100A Page GUIDE TO INSTALLATION OINT-TO-POINT INSTALLATION P MASTER/SLAVE LONWORKS INSTALLATION Page Page 1 INTRODUCTION 1.1 PRODUCT DESCRIPTION 1.2 APPLICATIONS Page 1.3 MODEL DESCRIPTION 0 1.3.1 Oscillating Mirror Models +25 -25 1 T .4 INDICA ORS 1.5 ACCESSORIES 2 INSTALLATION 2.1 PACKAGE CONTENTS 2.2 MECHANICAL MOUNTING 2.2.1 Mounting the Scanner 2.2.2 Mounting the Scanner with Accessories Page 2.3 ELECTRICAL CONNECTIONS 2.3.1 Main/Aux. Serial Interface and I/O Connector Main Interface RS232 Interface RS485 Full-Duplex Interface RS485 Half-Duplex Interface Auxiliary Interface Inputs Page Page Outputs 2.3.2 Lonworks Input/Output Connector Network Termination Lonworks Interface Page 2.3.3 Ethernet Connector Ethernet Interface 2.3.4 Power Supply 2.4 USER INTERFACE 2.5 POSITIONING THE SCANNER Page 2.6 TYPICAL LAYOUTS 2.6.1 Point-to-Point 2.6.2 Pass Through 2.6.3 RS232 Master/Slave DS8100A 1 2 Main Serial Interface A uxiliary Serial Interface * P.S. (Presence Sensor) connected to External Trigger/PS input. 2.6.4 Multiplexer 2.6.5 Local Lonworks Network Small Synchronized Network Page Large Synchronized Network Page Redundant System Multidata Network 2.6.6 Fieldbus Network 2.7 KEYPAD AND DISPLAY 2.7.1 Internal Net 2.7.2 Test Mode 3 SOFTWARE CONFIGURATION 3.1 GENIUS INSTALLATION 3.2 GUIDE TO RAPID CONFIGURATION 3.2.1 Wizard for Quick Reader Setup est Operating Mode T On Line Operating Mode Automa ic Op t erating Mode 3.2.2 Genius Network Setup Through Master Page Net-Autoset xpress Network Setup E Network Wizard Page 3 ive Slave Address Ass nment .2.3 Alternat ig 3.3 ADVANCED GENIUS CONFIGURATION 3 AMETER DEFAULT VALUES .4 PAR Page Page 4 READING FEATURES 4.1 ADVANCED CODE RECONSTRUCTION (ACR 4) 4.1.1 Tilt Angle for Advanced Code Reconstruction 4.2 PACKTRACK DS Scanner PackTrack Reference System 4.2.1 PackTrack Calibration for DS8100A Page 4.2.2 PackTrack Calibration for DS8100A Oscillating Mirror Models 4.3 P RMANC 4 ERFO E .3.1 Reading Conditions Page 4.4 READING DIAGRAMS DS8100A-2X10 (0.50 mm/20 mils) DS8100A-2X10 (0.38 mm/15 mils) DS8100A-3X00 (0.50 mm/20 mils) DS8100A-3X10 (0.38 mm/15 mils) DS8100A-3X20 (0.30 mm/12 mils) DS8100A-3X30 (0.25 mm/10 mils) DS8100A-3X05 DS8100A-3X15 (0.38 mm/15 mils) DS8100A-3X25 (0.30 mm/12 mils) DS8100A-3X35 (0.25 mm/10 mils) 5 MAINTENANCE 5.1 CLEANING .2 AUTOMATIC SCANNER REPLACEMENT (ASR) 5.2.1 ASR Network Configuration 5 5.2.2 Scanner Replacement Procedure 6 TROUBLESHOOTING Page Page 7 TURES TECHNICAL FEA Page GLOSSARY Page Page INDEX DATALOGIC S.p.A., Via Candini, 2 40012 - Lippo di Calderara Bologna - Italy