dCS 904 User Manual | Manual for Software Version 1.5x and 1.36 |
dCS Ltd | June 2000 |
|
|
TYPICAL APPLICATIONS
Using a dCS 904 to output DSD
Analogue source |
|
|
|
|
|
|
|
|
| DSD |
CH2 |
|
|
|
|
|
|
|
|
| |
CH1 |
|
|
|
|
|
|
|
|
| Out |
|
|
|
|
|
|
|
|
|
| |
CH1(L) | CH2(R) | Sensitivity Reference In | Reference Out AES1 | AES2 | AES3 | AES4 CH1 |
| CH2 | In | MAINS FUSE 2A(T) ON OFF |
PUSH | PUSH | PUSH |
|
|
|
|
|
|
|
|
|
| CH1(L) CH2(R) |
|
|
| In | Out |
| Remote | |
|
|
|
|
|
| Out | ||||
|
|
|
|
|
| 75R |
| |||
|
|
|
|
|
|
| Clk |
|
|
|
Analogue |
| Digital I/O |
|
|
|
|
|
|
|
|
Figure 4 – DSD output configuration
do this: Set DSD in the menu to On.
do this: Most likely (check your other equipment) you will need word clock. Make sure BNC O is set to CL64.
do this: Select your filter.
P3D units only:
do this: Set DSD to P3D or DSD4 instead of On as required
Using a Master Clock to Sync a dCS 904
Single, Dual or
Quad AES
dCS 904
CH1(L) | CH2(R) | Sensitivity | Reference In | Reference Out | AES1 | AES2 | AES3 | AES4 | CH1 |
| CH2 | In | MAINS FUSE 2A(T) ON OFF |
PUSH | PUSH |
| PUSH |
|
|
|
|
|
|
|
|
|
|
|
| CH1(L) CH2(R) |
|
|
|
|
|
| In | Out |
| Remote | |
|
|
|
|
|
|
|
|
| Out | ||||
|
|
|
|
|
|
|
|
| 75R |
| |||
|
|
|
|
|
|
|
|
|
| Clk |
|
|
|
Analogue |
|
| Digital I/O |
|
|
|
|
|
|
|
|
|
|
CH1
CH2
Analogue source
AES 1 | AES 2 | AES 3 | AES 4 |
| 1 |
Outputs |
|
|
| Outputs |
|
AES/EBU |
|
|
| Wordclock | 7 |
dCS 992
2 | 3 | 4 | 5 | 6 |
| In | Mains Fuse (2AT) | On Off |
|
|
|
|
| External | Loop | Remote |
|
8 | 9 | 10 | 11 | 12 | Sync |
| ||
| Out |
|
|
Figure 5 – Syncing a dCS 904 to a Master Clock
do this: Make sure
Manual part no: DOC135904 iss 2B2 | Page 24 | 135904ma2b2.pdf file available from website |
Contact dCS on + 44 1799 531 999 | email to: more@dcsltd.co.uk |
(inside the UK replace + 44 with 0) | web site: www.dcsltd.co.uk |