Manuals / DeLonghi / Kitchen Appliance / Oven

DeLonghi DE 91 MPS manual Enamelled Parts, Stainless Steel Surface, Glass Control Panel

Models: DE 91 MPS

1 40

Download 40 pages 49.98 Kb

Page 28

ENAMELLED PARTS

All the enamelled parts must be cleaned with a sponge and soapy water only or other non-abrasive products.

Dry preferably with a microfibre or soft cloth.

STAINLESS STEEL SURFACE

■CAUTION:

The stainless steel front surfaces (control panel, oven door) used in this oven are protected with a Special Lacquer to reduce finger-print marks. To avoid damaging this lacquer, do not clean the stainless steel with abrasive cleaners or abrasive cloths or scouring pads.

ONLY SOAP/WARM WATER MUST BE USED TO CLEAN THE STAINLESS STEEL SURFACES.

PAINTED PARTS AND SILKSCREEN PRINTED SURFACES

Clean using an appropriate product. Always dry thoroughly.

IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abra- sion. You are advised to use a soft cloth and neutral soap.

CAUTION: Do not use abrasive substances or non-neutral detergents as these will irreparably damage the surface.

GLASS CONTROL PANEL

Clean using an appropriate product. Always dry thoroughly.

Do not use harsh abrasive cleaners or sharp metal scrapers to clean the control panel since they can scratch the surface, which may result in shattering of the glass.

28

Image 28

DeLonghi DE 91 MPS manual Enamelled Parts, Stainless Steel Surface, Painted Parts And Silkscreen Printed Surfaces

Contents

INSTALLATION and SERVICE INSTRUCTIONS USE and CARE INSTRUCTIONS DE 91 MPSMULTIFUNCTION BUILT-IN OVEN DèLonghiDear Customer USING THE OVEN FOR THE FIRST TIME CONTENTSFire risk! Do not store flammable material in the oven IMPORTANT PRECAUTIONS AND RECOMMENDATIONSWARNING Taking care NOT to lift the oven by the door handle ELECTRICAL REQUIREMENTS INSTALLATIONN.B. The connection of the appliance to earth is mandatory REPLACING THE POWER SUPPLY CABLE REPAIRSFEEDER CABLE SECTION TYPE HO5RR-F 220ELECTRIC DIAGRAM Installation requires a com- partment as illustrated in figures 5 and FITTING REQUIREMENTSmin 853 FIXING THE OVEN OVEN DOOR LOWER TRIM AIR FLOW USING THE OVEN FOR THE FIRST TIME USE and CAREPOSE THE CATALYTIC PANEL WITHOUT THE HOLE ON THE RIGHT OVEN WALL GREASE FILTER TILTING GRILL fig TELESCOPIC SLIDING SHELF SUPPORTS Cleaning the sliding shelf supports To remove the telescopic sliding shelf supportsClock and Timer with “Touch-control” keys Power on light Cooking with multifunction ovenFunction selector Temperature light Thermostat GENERAL FEATURES OPERATING PRINCIPLESOVEN LIGHT TRADITIONAL CONVECTION COOKINGUPPER HEATING ELEMENT LOWER HEATING ELEMENTGRILLING FAN GRILL MULTI-FUNCTIONFAN FORCED DEFROSTUSING THE ROTISSERIE 1. Prepare the rotisserie support fig COOKING ADVICE Always grill with the oven door closedSIMULTANEOUS COOKING OF DIFFERENT FOODS Clock/Timer with “Touch control” keys keysUSING THE TIMER SETTING THE CLOCK“TOUCH-CONTROL” KEYS SETTING THE TIMER VOLUME AUTOMATIC COOKINGCLEANING and MAINTENANCE GENERAL ADVICEENAMELLED PARTS STAINLESS STEEL SURFACEPAINTED PARTS AND SILKSCREEN PRINTED SURFACES GLASS CONTROL PANELADVICE FOR USE AND MAINTENANCE OF CATALYTIC PANELS INSIDE OF OVENGRILL HEATING ELEMENT GREASE FILTERREPLACING THE OVEN LAMPS REMOVING AND REPLACING THE INNER DOOR GLASS PANE FOR CLEANING REMOVING THE DOOR REMOVING THE INNER PANE OF GLASS 1. Remove the oven door and place it on a soft surfaceIMPORTANT The door shall be placed horizontally as per figure 2. Press down on both tabs to release the glass retainerREMOVE THE INNER GLASS PANE Lift and remove the inner pane slightly, as shown in the figureAFTER CLEANING, REPLACE THE INNER GLASS PANE REPLACE THE GLASS RETAINER REFIT THE DOOR TROUBLESHOOTING Page Cod. 1103388-ß2