DeLonghi ETAM36.365 manual Making Milk Based Drinks, Making coffee using pre-ground coffee

-1 cup, if you want 1 coffee (fig. 15);

-2 cups if you want 2 coffees (fig. 17).

3.Lower the spout as near as possible to the cups (fig. 16). This makes a creamier coffee .

4.Press the button corresponding to the number of coffees

required (1 cup or 2 cups ).

5.Preparation begins. The amount of coffee selected is dis- played together with a progress bar which gradually fills as preparation progresses.

Please note:

•While the machine is making coffee, delivery can be in- terrupted at any moment by pressing one of the delivery buttons.

•At the end of delivery, to increase the quantity of coffee in

the cup, just press and hold (within 3 seconds) one of the

coffee buttons ( or ).

Once the coffee has been made, the appliance is ready to be used again.

Please note!

•Various alarm messages could be displayed while using the machine (FILL TANK, EMPTY GROUNDS CONTAINER, etc.). Their meaning is explained in the section “Displayed messages” (page 21).

•For hotter coffee, see the section “Tips for a hotter coffee”

(page 13).

•If the coffee is delivered a drop at a time, too weak and not creamy enough or too cold, read the tips in the “Trouble- shooting” section on page 22.

Making coffee using pre-ground coffee

Important!

•Never add pre-ground coffee when the machine is off or it could spread through the inside of the machine and dirty it. This could damage the appliance.

•Never use more than one level measure as it could dirty the inside of the machine or block the funnel.

Please note!

If you use pre-ground coffee, you can only make one cup of coffee at a time.

1.Press the aroma selection button (fig. 10) until “Pre-ground” is displayed.

2.Open the beans container lid, then open and raise the pre- ground coffee funnel lid.

3.Make sure the funnel is not blocked, then add one level measure of pre-ground coffee (fig. 18).

4.Place a cup under the coffee spouts.

5.Press the 1 cup button (fig. 15).

6.Preparation begins. The amount of coffee selected is dis- played together with a progress bar which gradually fills as preparation progresses.

Please note!

If “Energy saving” mode is active, you may have to wait a few seconds before the first coffee is delivered.

MAKING MILK BASED DRINKS

Please note!

•To avoid producing milk with poor froth or large bubbles, always clean the milk container lid and hot water nozzle as described in the section “Cleaning the milk container” on pages 15 and 18.

Filling and attaching the milk container

1.Remove the lid by pressing the release button C4 and at the same time lifting the lid upwards (fig. 19);

2.Fill the milk container with a sufficient quantity of milk, not exceeding the MAX level marked on the container (fig. 20). Each mark on the side of the container corresponds to about 100 ml of milk.

Please note!

•For a denser more even froth, you must use skimmed or partially skimmed milk at refrigerator temperature (about 5°C).

•If “Energy saving” mode is enabled, you may have to wait a few seconds before the drink is delivered.

3.Make sure the milk intake tube is correctly inserted in the bottom of the milk container lid (fig. 21).

4.Replace the lid on the milk container and press down- wards until it clicks in place.

5.Extract the hot water spout by pressing the button on the spout (fig. 22A)

6.Attach the milk container to the nozzle and push as far as it will go (fig. 23). The machine emits a beep (if the beep function is enabled).

7.Place a sufficiently large cup under the coffee and frothed milk spouts. Adjust the length of the milk spout. To move it nearer the cup, simply pull it downwards (fig. 24).

8.Follow the instructions below for each function.

Adjusting the amount of froth

Turn the froth adjustment dial to adjust the amount of froth on the milk delivered while making cappuccino and milk based coffees.

Dial	Description	Recommended for…
position

13