5. | Place the | filter in the | 39 | |||
| water tank and sub- | |||||
|
|
| ||||
| merge it completely for |
|
| |||
|
|
| ||||
| ten seconds, tilting it to |
|
| |||
| enable the air bubbles |
|
| |||
| to escape (fig. 39). |
|
|
| ||
6. | Insert the filter into the |
|
| |||
| filter housing and press |
|
| |||
| as far as it will go | (fig. |
|
| ||
| 40A). |
|
|
|
| 40A |
7. Close the tank with the |
|
| ||||
| lid (fig. 40B), and then |
|
| |||
| replace the tank in the |
|
| |||
| machine. |
|
|
|
| |
When you install the filter, |
|
| ||||
you must notify the appliance |
| 40B | ||||
of its presence. | MENU/ESC |
| ||||
8. | Press | the |
|
| ||
| button | to | enter | the |
|
|
| menu; |
|
|
|
|
|
9.Press the scrolling arrow (< or >) (fig. 9) until “Install filter” is displayed.
10. | Press the | button. |
|
11. | “Install?” is displayed; |
| |
12. | Press the | button to confirm | the selection. “Wa- |
| ter delivery Press OK” is displayed. |
| |
13. | Position a container under the hot water spout (min. ca- | ||
| pacity: 100 ml). |
|
|
14. | Press the | button to confirm | the selection. The |
| appliance begins hot water delivery and the message | ||
| “Please wait” is displayed. |
| |
15. | After delivery, the appliance is automatically ready to make | ||
the next drink.
The filter is now active and you can use the coffee machine.
Replacing the filter
When the symbol “
” is displayed together with the mes- sage“REPLACE FILTER”, after two months (see date indicator) or when the appliance has not been used for 3 weeks, you should replace the filter:
1.Extract the tank and exhausted filter;
2.Remove the new filter from the packaging and proceed following steps from 2 to 6 of the paragraph before.
3.Position a container with a minimum capacity of 100 ml under the hot water spout.
4.Press the MENU/ESC button to enter the menu;
5.Press < or > until “Replace filter” is displayed.
6. | Press the | button; |
7. | “Confirm?” is displayed; | |
8. | Press the | button to confirm the selection; |
9. | “Water delivery, Press OK” is displayed. | |
10. | Press the | button to confirm the selection. The |
| appliance begins hot water delivery and the message | |
| “Please wait” is displayed. | |
11.After delivery, the appliance is automatically ready to make the next drink.
The new filter is now active and you can use the coffee ma- chine.
Removing the filter
If you want to use the appliance without the filter, you must remove it and notify the appliance of its removal.
Proceed as follows:
1.Extract the tank and exhausted filter;
2.Press the MENU/ESC button to enter the menu;
3.Press the scrolling arrow (< or >) (fig. 9) until “Install fil- ter, Installed” is displayed.
4.Press the 
button;
5.The message “Uninstall?” appears on the display;
6. Press the 
button to confirm and theMENU/ESC button to exit the menu.
Electrical connection (UK only)
A)If your appliance comes fitted with a plug, it will incorporate a 13 Amp fuse. If it does not fit your socket, the plug should be cut off from the mains lead, and an appropriate plug fitted, as below. WARNING: Very carefully dispose of the cut off plug after removing the fuse: do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard. With alternative plugs not incorporating a fuse, the circuit must be protected by a 15 Amp fuse. If the plug is a
B)If your appliance is not fitted with a plug, please follow the instructions provided below:
WARNING - THIS APPLIANCE MUST BE EARTHED
| important |
green and yellow | earth |
blue | NEUTRAL |
brown | LIVE |
As the colours of the wires in the mains lead may not correspond with the col- oured markings identifying the terminals in your plug, proceed as follows:
The green and yellow wire must be connected to the terminal in the plug marked
with the letter E or the earth symbol 
or coloured green or green and yel- low.
The blue wire must be connected to the terminal marked with the letter N or coloured black.
The brown wire must be connected to the terminal marked with the letter L or coloured red.
19
