DeLonghi ETAM36.365 manual Energy saving, Setting the temperature, Setting water hardness, Beep

3.	Press the	button;
4.	Press the scrolling arrow (< or >) (fig. 9) until the number
	of minutes/hours of operation is displayed (15 or 30 min-
	utes, or 1, 2 or 3 hours);
5.	Press the	button to confirm;

6.Press the MENU/ESC button to exit the menu. Auto-off is programmed.

Energy saving

Use this function to enable or disable energy saving.

When enabled, the function reduces energy consumption in compliance with European regulations.

To disable (or enable) energy saving, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Energy saving” is displayed;

3.	Press the	button. “Disable?” is displayed (or “En-
	able?” if the function has already been disabled);
4.	Press the	button to disable (or enable) energy
	saving mode;
5.	Press the MENU/ESC button to exit the menu.

When the function is active, “Energy saving” is displayedafter a period of inactivity.

Please note!

•When in energy saving mode, a few seconds elapse before the first coffee, cappuccino or milk based coffee is deliv- ered as the appliance must heat up again.

•To prepare a drink, press any button to exit energy sav- ing, then press the button corresponding to the drink you want to make.

•If the milk container is attached to the appliance, the en- ergy saving function is not active.

Setting the temperature

To modify the temperature of the water used to make the cof- fee, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Set tem- perature” is displayed;

3. Press the button;

4.Press the scrolling arrow (< or >) until the required tem- perature is displayed (●=low; ●●●●=maximum);

5. Press the button to confirm;

6.Press the MENU/ESC button to exit the menu.

Setting water hardness

For instructions on setting water hardness, see page 19.

Setting the language

To modify the language of the display, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Set lan-

guage” is displayed;
3. Press the	button;

4.Press the the scrolling arrow (< or >) until the required language is displayed ;

5. Press the button to confirm;

6.The set language is displayed;

7.Press the MENU/ESC button to exit the menu.

Beep

This enables or disables the beep emitted by the machine each time the buttons are pressed or an accessory is inserted/re- moved. To disable or re-enable the beep, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Beep” is displayed;

3.	Press the	button. “Disable?” is displayed (or “En-
	able?” if disabled);
4.	Press the	button to enable or disable the beep;
5.	Press the MENU/ESC button to exit the menu.

Cup lighting

This function enables or disables the cup lighting. The lighting is enabled by default.

The lighting comes on each time coffee, cappuccino or milk based coffee is made and during each rinsing cycle.

To disable or re-enable this function, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Cup light- ing” is displayed;

3.	Press the	button. “Disable?” is displayed (or “En-
	able?” if disabled);
4.	Press the	button to enable or disable the cup
	lighting;
5.	Press the MENU/ESC button to exit the menu.

Default values (reset)

This resets all menu settings and programmed quantities back to the default values (with the exception of the language which remains as set).

To reset the default values, proceed as follows:

1.Press the MENU/ESC button to enter the menu;

2.Press the scrolling arrow (< or >) (fig. 9) until “Default values” is displayed;

3.Press the button;

4.“Confirm?” is displayed;

5. Press the button to confirm and exit.

Statistics function

This displays statistics relating to the machine.

11