System Setup
Setting items | Setting details |
|
|
Channel Level | Test Tone Start : Output test tone. |
Set the volume of the test | • Front L / F.Height L / Center / F.Height R / Front R / Surround R / |
tone to be the same when it S.Back Rz / S.Back Lz / Surround L / Subwoofer : Select the speaker. is output from each speaker. zz When the “Speaker Config.” – “S.Back” setting (vpage 60) is set
to “1spkr”, “S.Back” is displayed.
•
When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 43.
NOTE
•Speakers set to “None” in the “Speaker Config.” (vpage 60) settings are not displayed.
•When a headphones jack is inserted in the PHONES jack of this unit, the “Channel Level” is not displayed.
Default : The “Channel Level” settings are returned to the default settings.
•Yes : Reset to the defaults.
•No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Return settings to the default?” prompt
is displayed. Select either “Yes” or “No”, and press ENTER.
BD | 62 |
Setting items | Setting details | |
|
| |
Crossover Freq. | Crossover : Set the crossover frequency. | |
Set the maximum frequency | • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / | |
of the bass signal output | 250Hz | |
from each channel to | Advanced : Specify crossover frequency for each speaker. | |
the subwoofer. Set the | ||
• Front / Center / Surround / S.Back / F.Height : Select the speaker. | ||
Crossover Frequency to | ||
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / | ||
suit the bass reproduction | ||
250Hz : Set the crossover frequency. | ||
capability of the speaker | ||
| ||
being used. |
| |
| • “Crossover Freq.” can be set when the “Bass Setting” – “Subwoofer | |
| Mode” (vpage 61) setting is “LFE+Main”, or when you have a | |
| speaker that is set to “Small”. | |
| • Always set the crossover frequency to “80Hz”. When using small | |
| speakers, however, we recommend setting the crossover frequency to | |
| a higher frequency. | |
| • For speakers set to “Small”, sound below the crossover frequency | |
| is cut from the sound output. The cut bass sound is output from the | |
| subwoofer or front speakers. | |
| • The speakers that can be set when “Advanced” is selected differ | |
| depending on to the “Subwoofer Mode” setting (vpage 61). | |
| • When “LFE” is selected, speakers set to “Small” at “Speaker Config.” | |
| can be set. If the speakers are set to “Large”, “Full Band” is displayed | |
| and the setting cannot be made. | |
| • If set to “LFE+Main”, this setting can be made regardless of the | |
| speaker size. | |
Front Sp Setup | 2CH DIRECT/STEREO : The front speakers used in the direct, stereo and | |
Set the front speakers to | pure direct play modes (2 channel) are set in advance. | |
use for every surround | • A : Front speaker A is used. | |
mode. | • B : Front speaker B is used. | |
NOTE | • A+B : Both front speakers A and B are used. | |
MULTI CH : The front speakers used in modes other than the direct, | ||
This can be set when “Amp | ||
stereo and pure direct play modes (2 channel) are set in advance. | ||
Assign” is set to “Front B” | • A : Front speaker A is used. | |
(vpage 60). | • B : Front speaker B is used. |
• A+B : Both front speakers A and B are used.
vSee overleaf
version Basic
version Advanced
Information