System Setup
Setting items | Setting details | ||
|
|
|
|
GUI | Screensaver : Make screensaver settings. |
|
|
Make the settings related to • ON : The screensaver is activated during menu
displays on the TV screen. | display, iPod or TUNER screen display if no |
| operation is performed for an approximately |
| |
| uio p, the screensaver is cancelled and |
| the screen before that screen saver started is |
| displayed. |
| • OFF : Screensaver is not activated. |
Format : Set the video signal format to be output for the TV you are using.
•NTSC : Select NTSC output.
•PAL : Select PAL output.
“Format” can also be set by the following procedure. However, the menu screen is not displayed.
1.Press and hold the main unit’s 2 and 9 for at least 3 seconds. “V.Format:<NTSC>” appears on the display.
2.Press the main unit’s TUNER PRESET CH +, – and set the video signal format.
3.Press the main unit’s iPod 1 to complete the setting.
NOTE
When a format other than the video format of the connected TV is set, the picture will not be displayed properly.
Text : Display the details of operation when switching surround mode, input mode, etc.
•ON : Turn display on.
•OFF : Turn display off.
Master Volume : Display the master volume during adjustment.
•Bottom : Display at the bottom.
•Top : Display at the top.
•OFF : Turn display off.
When the master volume display is hard to see when superimposed on movie subtitles, set to “Top”.
iPod : Set the iPod screen display time when the input source is “DOCK”.
•Always : Show display continuously.
•30s : Show display for 30 seconds after operation.
•10s : Show display for 10 seconds after operation.
•OFF : Turn display off.
BD | 66 |
Setting items | Setting details |
|
|
GUI | Tuner : Set the tuner screen display time when the input source is |
(Continued) | “Tuner”. |
| • Always : Show display continuously. |
| • 30s : Show display for 30 seconds after operation. |
| • 10s : Show display for 10 seconds after operation. |
| • OFF : Turn display off. |
Remote Setup Guide | See “Registering preset codes” (vpage 75). |
Search a preset code to |
|
register in the remote |
|
control unit. |
|
Quick Sel.Name | • Up to 16 characters can be input. |
Change the “Quick Select” | • For character input, see page 50. |
display title to one you |
|
prefer. |
|
Zone Rename | • Up to 10 characters can be input. |
Change the display title of | • For character input, see page 50. |
each zone to one you prefer. |
|
Dimmer | Bright : Normal display brightness. |
Adjust the display | Dim : Reduced display brightness. |
brightness of this unit. | Dark : Very low display brightness. |
| OFF : Turns the display off. |
Buttons on the main unit can be used for operations.
Each time DIMMER is pressed, the setting is changed as shown below.
|
|
|
| Bright |
|
| Dim |
|
| ||
|
|
|
| OFF |
|
|
| Dark |
|
| |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
Setup Lock | ON : Turn protection on. |
|
|
|
|
|
| ||||
Protect settings from | OFF : Turn protection off. |
|
|
|
|
|
| ||||
inadvertent change. | When canceling the setting, set “Setup Lock” to “OFF”. | ||||||||||
| |||||||||||
NOTE
When “Setup Lock” is set to “ON”, the settings listed below can no longer be changed. Also, “Setup Lock!” is displayed if you attempt to operate related settings.
• Menu operations | • Channel Level |
|
|
version Basic
version Advanced
Information