Denon DN-A7100 manual Preference, Surround

ENGLISH

3 PREFERENCE

3 PREFERENCE
STANDBY MODE	: ECONOMY
TV-AUTO	:
OSD INFO	: ENABLE
BILINGUAL	: MAIN
VIDEO CONVERT
HDMI	: ENABLE
DC TRIGGER
MAIN	EXIT

1. Select “PREFERENCE” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.

2. To select a desired content, press the 3 or 4 cursor buttons.

STANDBY MODE:

When this function is set to “ECONOMY”, you can reduce the power consumption when the unit is in the standby mode.

Note:

TV-AUTO and RS-232C are disabled in the “ECONOMY” setting.

TV AUTO:

Select the TV AUTO ON/OFF function to enable or disable with the 1 or 2 cursor buttons.

OSD Info:

Select the OSD information function to enable or disable with the 1 or 2 cursor buttons.

If you select “ENABLE”, the DN-A7100 will display the status of the feature (Volume up/down, input select, etc..) on the TV monitor. But if you do not desire this information, select “DISABLE”.

BILINGUAL:

In the Bilingual mode, Dolby Digital and DTS output is set to either “MAIN” or “SUB”. Select “BILINGUAL” with the 1 and 2 cursor buttons, then select MAIN ↔ SUB ↔ MAIN+SUB with the 1 or 2 cursor buttons.

VIDEO CONVERT:

Select the VIDEO CONVERT function to enable or disable with the 1 or 2 cursor buttons. (Video cable connection: Refer to page 15)

3-1 VIDEO CONVERT

TV : ON

DVD : ON

VCR1 : ON

DSS : ON

AUX1 : ON

MAIN RETURN EXIT

After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.

HDMI AUDIO:

This setting determines whether to playback audio input to the HDMI jacks through the DN-A7100 or output it through the receiver to a TV or projector. ENABLE: The audio input to the HDMI jacks can be played back by this receiver.

In such case, audio signals are not output to the TV or projector.

THROUGH: The audio input to the HDMI jacks is not output from the output terminals of the DN-A7100. Audio data is output directly to the TV or projector. This setting is used to listen to audio on a multi channel TV, etc.

DC TRIGGER:

Select “DC TRIG SETUP” in the SETUP MAIN MENU with 3 or 4 cursor button, and press the ENTER button.

3-2 DC TIRGGER SETUP DC TRIG DISABLE

TV	:	CD	:
DVD	:	TAPE :
VCR1	:	CD-R :
DSS	:	AUX2 :
AUX1	:	TUNER:
		7.1CH:
MAIN	RETURN		EXIT

You can select MAIN ROOM, REMOTE or DISABLE by pressing 1 or 2 cursor buttons.

Notes:

•REMOTE is available for the external control. The RC-1065 cannot operate this function.

•To select desired input source , press 3 or 4 cursor button.

•To set ON or OFF, press 1 or 2 cursor button.

•After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.

4 SURROUND

4 SURROUND

SURR.MODE :AUTO

HT-EQ :OFF

LFE LEVEL :

MAINEXIT

1. Select “SURROUND” in the SETUP MAIN MENU with the 3 or 4 cursor buttons, and press the ENTER button.

2. To select a desired content , press the 3 or 4 cursor buttons.

SURR.MODE:

Select the desired surround mode with the 1 or 2 cursor buttons.

HT-EQ:

Select to active the HT-EQ with the 1 or 2 cursor buttons.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments.

Activating the HT-EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance.

The HT-EQ feature is available except in the following modes.

•7.1 CH INPUT

•PURE-DIRECT

•When VIRTUAL is set for the surround mode

LFE LEVEL:

Select the output level of the LFE signal included in

the Dolby Digital signal or the DTS signal.

Select 0 dB, -10 dB or OFF with the 1 or 2 cursor buttons.

After you complete this portion of the set up, move the cursor to “MAIN” with the 3 or 4 cursor buttons and press the ENTER button.

22