Denon DN-A7100 manual Specific Commands

Surround contents

	Command			Reply from Slave
	AUTO		“SUR:00”
	STEREO		“SUR:01”
	DOLBY		“SUR:02”
	PL2xMOVIE		“SUR:03”
	PL2 MOVIE		“SUR:04”
	PL2xMUSIC		“SUR:05”
	PL2 MUSIC		“SUR:06”
	PL2xGAME		“SUR:07”
	PL2 GAME		“SUR:08”
	Dolby PROLOGIC		“SUR:09”
	EX/ES		“SUR:0A”
	VIRTUAL 6.1		“SUR:0B”
	-		-
	DTS ES		“SUR:0E”	“SUR:x“
Surr. Mode	NEO6 CINEMA		“SUR:0F”
				(x = ‘0’ ~’Z’)
	NEO6 MUSIC		“SUR:0G”
	Multi Ch. STEREO		“SUR:0H”
	CSII CINEMA		“SUR:0I”
	CSII MUSIC		“SUR:0J”
	CSII MONO		“SUR:0K”
	VIRTUAL		“SUR:0L”
	DTS		“SUR:0M”
	DD+ PL2x MOVIE		“SUR:0O”
	DD+ PL2x MUSIC		“SUR:0P”
	-		-
	SOURCE DIRECT		“SUR:0T”
	PURE DIRECT		“SUR:0U”
	UP		“SUR:1”
	DOWN		“SUR:2”
	Command			Reply from Slave
	TOGGLE		“TTO:0”
Test Tone	OFF		“TTO:1”	“TTO:1xy” (OFF),
(Force start/stop Test	ON		“TTO:2”	“TTO:2xy” (ON, x= auto(0)/
Tone with Auto mode)	NEXT		“TTO:3”	manual(1), y= ch.)
	PREV		“TTO:4”
	TOGGLE		“NGT:0”	“NGT:1”(OFF),
Night Mode	OFF		“NGT:1”
				“NGT:2”(ON)
	ON		“NGT:2”
	Command			Reply from Slave
		“LIP:0xxx” (xxx = value)
	VALUE		xxx = 000 (OFF),	“LIP:xxx”
		xxx = 010,020,...190,200		(xxx = Lip Sync. value)
Lip Sync.
			(ms)	xxx = 000 (OFF),
	UP		“LIP:1”	xxx = 010,020,...190.200 ms
	DOWN		“LIP:2”

Tuner contents

	Command		Reply from Slave
	VALUE	“TFQ:0xxxxx”	“TFQ:xxxxx”
		(xxxxx = freq.)
			(xxxxx = Frequency)
Tuner Frequency	UP	“TFQ:1”
			if (xxxxx < 02000) band=AM;
	DOWN	“TFQ:2”
			else band=FM;
	Auto-UP	“TFQ:3”
			(ex.“08750” = FM87.50MHz)
	Auto-DOWN	“TFQ:4”
	VALUE	“TPR:0ww”
	UP	“TPR:1”	“TPR:ww”
Tuner Preset	DOWN	“TPR:2”	(ww = current preset nr.)
	P-Scan start	“TPR:3”	(ww = 01 ~ ??)
	P-Scan stop	“TPR:4”
	TOGGLE	“TMD:0”	“TMD:0”( - ),
Tuner mode	OFF(MONO)	“TMD:1”	“TMD:1” (MONO),
	ON(AUTO)	“TMD:2”	“TMD:2” (AUTO)
Tuner RDS	DISP	“RDS:3”	ACK
	PTY	“RDS:4”
Tuner MEMO	-	“MEM:0”	ACK
CLEAR	-	“CLR:0”	ACK
	Key0,	“NUM:0” ,
	Key1,	“NUM:1” ,
	Key2,	“NUM:2” ,
	Key3,	“NUM:3” ,
Tuner Numeric keys	Key4,	“NUM:4” ,	ACK
	Key5,	“NUM:5” ,
	Key6,	“NUM:6” ,
	Key7,	“NUM:7” ,
	Key8,	“NUM:8” ,
	Key9	“NUM:9”

Specific Commands

	Command from Host		Reply from Slave
Auto status feedback		“AST:x” (x = ‘0’ ~ ’F’)
		bit 3 : Layer 4 ( 1 = Enable, 0 = Disable)	same as
(The product default is all auto		bit 2 : Layer 3 ( 1 = Enable, 0 = Disable)	command define
		bit 1 : Layer 2 ( 1 = Enable, 0 = Disable)
status feedback disabled.)
		bit 0 : Layer 1 ( 1 = Enable, 0 = Disable)

ENGLISH

41