ENGLISH

@5 TITLE/ID3, C-FADE button

TITLE/ID3:

When an MP3/WAV file has ID3 Tag data, the artist name, album name, genre, BPM, and year are displayed.

C-FADE:

Switches cross-fading on and off.

@6FLIP/CLR button

FLIP:

Use this to select operating mode of A1 and A2 buttons, from Hot Start mode and Stutter mode. The display will indicate “H/S” or “STR”.

A1, A2 CLR:

If the A1 or A2 button is pushed while pushing the FLIP button, you can clear the selected A point. By holding down just the FLIP button for more than 1 sec, you can clear A1 and A2 points all at once.

@7A1, A2 button

Using this button you can create starting point for Hot Start, Seamless Loop and Stutter.

@8A/B TRIM buttons

When the button is pressed during playback, the *A/B TRIM MODE is selected. *Only when a seamless LOOP is set.

@9B button

Use this to set the B point for to create a Seamless Loop after the A point has been set.

#0EXIT/RELOOP button

Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function.

#1PLAY LIST button

Switches the playback mode.

File Play:

Selects and plays an MP3/WAV file.

Playlist Play:

Selects a playlist file and plays the MP3/WAV files registered on that playlist (up to 99 songs can be registered).

#2 CONT./SINGLE, RELAY button

CONT./SINGLE:

A short tap of this button will toggle between 3 possible END modes for playback CONT. (continue: plays all files) SINGLE (stops playing and ReCUE’s back to your original set point), PLAYLOCK-see below.

SINGLE PLAY LOCK:

SINGLE PLAY LOCK can be selected by PRESET. When SINGLE PLAY LOCK is selected, file selection during playback is disabled. This prevents playback from stopping when the PARAMETERS knob is turned accidentally during playback. Play ending mode is the same as single.

RELAY:

You can turn on and off RELAY PLAY mode.

#3PARAMETERS knob

PARAMETERS:

When the PARAMETER indicator is flashing, turn this knob to select and change the parameter for items found in the Platter effects, Memo, and Preset data, etc.

FILE SEARCH:

When PARAMETER indicator is on, turn this knob to select files.

#4BACK button

Press this button to return to the previous screen. A long-press shall return to the top menu.

#5#6FAST SEARCH (7) QUICK JUMP button

FAST SEARCH (6), QUICK JUMP button

QUICK JUMP:

When one of these buttons is tapped shortly, the playback position jumps approximately 10 seconds in the reverse (6) or forward (7) direction. The jump time can be changed in the preset mode.

FAST SEARCH:

When one of these buttons is pressed and held in, the disc is fast-searched in the reverse (6) or forward (7) direction.

#7DEVICE button

Press this button to select the source (HDD, USB1 to 4).

#8MIDI button

• Use this to switch to the USB MIDI Control mode.

#9D-SYNC button

Use this to turn the D-SYNC mode on and off.

This function allows you to control the Deck 2 side of the other DN-HS5500 connected by cable.

(This is as if the unit for which the button is pressed becomes the controller.)

$0PITCH SLIDER

Use this slider to adjust playing speed.

The playing speed decreases when slid upwards and increases downwards.

$1KEY ADJUST button

• Use this to turn the key adjust mode on and off.

$2$3PITCH BEND ± buttons

Pushing these buttons will change main playing speed temporarily.

While pushing PITCH BEND + button the playing speed increases and speed decreases while pushing PITCH BEND – button.

When release button, playing speed returns to the previous speed.

$4 PITCH, RANGE button

PITCH:

The pitch mode turns on and off each time this button is pressed shortly and released.

The PITCH LED lights when the pitch mode is on.

RANGE:

Push this button for more than 1 sec to select the pitch range. The pitch range can be selected with the PARAMETERS knob from ±4, 10, 16, 24, 50 or 100 %.

$5PLATTER SOURCE button

Select from Scratch playback, Bend mode, File search or Manual Frame Search mode.

SCRATCH:

This button lights up or blinks in orange when scratching. Manipulate the sound by pushing down on the PLATTER disc.

BEND/SEARCH:

When the PLATTER Source is set to BEND during playback, it alternates as the pitch bend function. The display will indicate “Bend”. When PLATTER Source is set to Search, during Pause or CUE mode, it alternates as the Manual Search function. Manual search allows you to move the CUE point around by one frame at a time (1/75 second) with an audible frame-repeat sound. The display will indicate “Search”.

$6Platter LED

This LED indicates the scratch memory and platter mode.

$7REVERSE button

• Push this button to set the REVERSE.

$8DUMP button

• Push this button to set the DUMP.

$9BRAKE button

Push this button to set the BRAKE and adjust the parameter.

%0MIRROR MIX button

Press this button for over 1 second to turn the mirror mix mode on and off.

When in the mirror mix mode, if the button is pressed shortly and released, the mirror mix delay time can be selected with the PARAMETERS knob.

7

ENGLISH