Denon DVD-2910, DVD-955 12 USING THE VIDEO SETUP

ENGLISH

12 USING THE VIDEO SETUP

2The video output setting of the HDMI and the DVI-D connectors can be changed.

2The video output setting of the PICTURE MODE, PROGRESSIVE MODE and ADJUST MODE also can be changed.

	PLAY	STOP
	OPEN/CLOSE
ON / STANDBY	STILL / PAUSE
	SUPER	PURE
	AUDIO CD	DIRECT	HDMI / DVI
	SETUP	SELECT	SELECT	FORMAT
	DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER DVD-2910

Display the setting mode

1 2

✽ The HDMI, DVI, 480P, 576P, 720P and 1080i indicators flash when the connection is being checked, then stop flashing, remaining lit, once the check is completed.

					1 2
							PO
							WER
							OFF
					SE	H
					LECT DM		I/DVI
						FO
							RMAT	NTSC		PO
										WERO
									/PAL	N
										C O
										LOSPEN/
							S			E
							UP
							CD	ER
								SET	AU
						PR			UP DIO
						/D	OG
				SEA			RA
		T					IRECT M
		OPM	A	RC	CL
		EN	NG	HM
		U	LE	ODE	EAR
			S		C
			UBT		ALL
			ITLE
	ME			AU
				DIO
	NU		D
			ISP
			LAY
	S
	TOP
	S
	TIL
SK	L/PA	RETU
	USE		RN
IP		PLAY
A-B
	S
	LOW
	/SEA
	RCH
ZO	PA
	GE
OM
	DIM

	Press the HDMI/DVI SELECT button.
	• The modes described below will appear on the display.
	HDMI/DVI OFF (Factory default)	HDMI / DVI		HDMI/DVI OFF
	No output signals from the HDMI and DVI-D	SELECT	FORMAT
	connectors.
	This mode is set to use the COMPONENT VIDEO
	OUT connector.			HDMI Y Cb Cr
	HDMI Y Cb Cr	Main unit
1
	Outputs the component signals from the HDMI
	connector.	HDMI/DVI
	HDMI RGB
		SELECT	FORMAT	HDMI R G B

Outputs the RGB signals from the HDMI connector.

DVI
Outputs the RGB signals from the DVI-D connector.
✽The video signals are only output from one of the	Remote control unit	DVI
HDMI, DVI or progressive component video output
connectors.

Press the HDMI/DVI FORMAT button.

•The modes described below will appear on the display. Select the item you wish to set and press the select

knob to define it.

	480P/576P (Factory default)				480P/576P
	Outputs the image from the HDMI or DVI-D connector
	at 480P (NTSC) or 576P (PAL).		HDMI / DVI
		SELECT		FORMAT
	720P
					720P
	Outputs the image from the HDMI or DVI-D connector
	at 720P.
	1080i
2	Outputs the image from the HDMI or DVI-D connector		Main unit		1080i
	at 1080i.
	• When playing back a PAL-formatted disc, be sure to		HDMI/DVI
		SELECT		FORMAT
	set the TV TYPE option to NTSC. (See pages 32, 33.)
	• The video or audio signals may be interrupted when
	the output setting mode is switched.
	• Depending on the TV you are using, if the TV’s input	Remote control unit
	is not set to HDMI or DVI, the HDMI or DVI OFF
	mode may be set. In this case, set the TV’s input
	setting to HDMI or DVI before performing the DVI
	setup procedure.

•Connect to an HDCP compatible display to view images with DVI connections.

49