ENGLISH
Started Getting
Troubleshooting
Specifications Troubleshooting Functions Other Timer the Setting Playback Setup Connections
If a problem should arise, first check the following:
1.Are the connections correct?
2.Is the set being operated as described in the owner’s manual?
3.Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
GGeneralH
Symptom |
| Cause |
|
| Countermeasure |
|
| Page | |||
Set does not | • External noise or interference is | • Reset the microprocessor. |
| 22 | |||||||
operate properly. | causing the set to malfunction. |
|
|
|
|
|
| ||||
When the power | • Connection of the power cord is | • Check that the power plugs are | 10 | ||||||||
is turned on, the | faulty. |
|
|
| securely inserted into the RCD- |
| |||||
power indicator |
|
|
|
|
| CX1’s AC inlet and the wall power |
| ||||
does not light |
|
|
|
|
| outlet. |
|
|
|
|
|
and no sound is |
|
|
|
|
|
|
|
|
|
|
|
produced. |
|
|
|
|
|
|
|
|
|
|
|
The power | • The | speaker | cables | are | not | • Connect securely. |
|
| 8 | ||
indicator lights | properly connected. |
|
|
|
|
|
|
|
| ||
but no sound is | • The function (input) is incorrect. | • Switch | to the | correct | function | 12 | |||||
produced. |
|
|
|
|
| (input). |
|
|
|
|
|
| • The volume is set too low. |
| • Adjust | the | volume | to | an | 12 | |||
|
|
|
|
|
| appropriate level. |
|
|
| ||
No sound is | • The | speaker | cables | are | not | • Connect securely. |
|
| 8 | ||
produced from | properly connected. |
|
|
|
|
|
|
|
| ||
one side. | • The input cables are not properly | • Connect securely. |
|
| 8, 9 | ||||||
| connected. |
|
|
|
|
|
|
|
|
| |
| • The left/right balance is off. |
| • Adjust the left/right balance. |
| 13 | ||||||
For stereo | • The connections of the speaker | • Check | and | remedy | the | 8 ~ 10 | |||||
sources, the | cables or input cables are | connections. |
|
|
|
| |||||
positions of the | inverted. |
|
|
|
|
|
|
|
|
| |
instruments are |
|
|
|
|
|
|
|
|
|
|
|
inverted. |
|
|
|
|
|
|
|
|
|
|
|
GCDH
Symptom |
| Cause |
| Countermeasure | Page |
Disc tray does not | • The power is not on. |
| • Turn on the power. | 12 | |
open. |
|
|
|
|
|
“NO DISC” is | • The disc is not properly loaded. | • Reload the disc. | 3 | ||
displayed even |
|
|
|
|
|
though a disc is |
|
|
|
|
|
loaded. |
|
|
|
|
|
“00 : 00” is | • A disc other than a CD or Super | • Load a CD or Super Audio CD. | 3 | ||
displayed even | Audio CD is loaded. |
|
|
| |
though a disc is |
|
|
|
|
|
loaded. |
|
|
|
|
|
Playback does not | • The disc is dirty or scratched. | • Wipe the dirt off the disc or | 3, 4 | ||
start even when |
|
|
| replace the disc. |
|
the 1/3 button is |
|
|
|
|
|
pressed. |
|
|
|
|
|
No digital signals | • For Super Audio CDs, no digital | • For Super Audio CDs, use the | 9 | ||
are output. | signals are output. |
| analog audio output signals. |
| |
| • Turn the pure direct mode on. | • Turn the pure direct mode off. | 13 | ||
A specific section | • The disc is dirty or scratched. | • Wipe the dirt off the disc or | 3, 4 | ||
of the disc |
|
|
| replace the disc. |
|
cannot be played |
|
|
|
|
|
properly. |
|
|
|
|
|
Programmed | • The | tracks have | not been | • Program properly. | 15 |
playback is not | programmed properly. |
|
| ||
possible. |
|
|
|
|
|
A | • The disc has not been finalized. | • Finalize the disc then play it. | 3 | ||
disc cannot be | • The recording conditions are bad | • Use a properly recorded disc. | – | ||
played. | or the quality of the disc itself is |
|
| ||
| poor. |
|
|
| |
Files recorded | • You | have selected a | copyright- | • Press the 8or 9button to | 16 |
in MP3 or WMA | protected WMA file or a file that | select a different file. |
| ||
format cannot be | cannot be played normally. |
|
| ||
played. |
|
|
|
|
|
23