ENGLISH
Getting | Connecting the System |
|
|
|
|
|
| ||
A home theater can be achieved easily using the included cables to connect the DVD surround receiver | |||||||||
Started |
|
| |||||||
|
|
|
|
|
|
| |||
Connections |
|
| The | set includes |
|
| |||
|
|
|
|
| |||||
Setup |
|
| a | clock |
|
| |||
|
| function. Connect |
|
| |||||
|
|
|
|
| |||||
|
|
| the | set’s | power |
|
| ||
RemotePlayback | Systemcable |
| cord |
| to | a wall | 3 | ||
| Power cord |
| outlet | to |
|
| |||
|
| White | power |
|
| ||||
|
|
| which | power | is |
|
| ||
|
| Red | always supplied. |
|
| ||||
|
|
|
|
|
|
|
| White | Red |
Control |
|
| To household |
|
|
|
| ||
|
| power outlet |
|
|
|
| |||
|
|
|
|
|
|
| |||
Information |
|
| (AC 120 V, 60 Hz) |
|
|
| |||
|
| Speaker cable |
|
|
| ||||
|
|
| Speaker cable |
|
|
| |||
Troubleshooting |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| TV |
| |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| 7*%&0 |
|
|
|
|
|
|
|
|
| */ |
|
|
|
|
|
|
| Video cable |
|
| |
NOTE
• Connect the set's video output directly to the TV. Do not connect it via a VCR (video cassette recorder). Some discs contain copy prohibit signals, and the picture could be disturbed if such discs are played via a VCR.
• Insert the plugs securely. Incomplete connections will result in the generation of noise.
• Do not unplug the power cord while the set is operating.
• When connecting system cables and speaker cables, first lay them out sideways. When laying them out take care not to damage them.
Protector circuit
The protection circuit will be activated in the following cases:
•When the speaker output is
•When the temperature around the set is extremely high
•When the set is used for long periods of time with a high output and the internal temperature rises
When the protection circuit is activated, the speaker output is cut off and the power supply indicator flashes. Should this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center.
Note on speaker impedance
If speakers with an impedance below the specified impedance (4 Ω/ohms) are used (for example, speakers with an impedance of 3 Ω/ohms) with the volume turned up high for long periods of time, the temperature may rise, activating the protective circuit.
When the protection circuit is activated, the output to the speakers is cut off and the power indicator blinks. If this happens, unplug the power supply cord, wait for the set to cool off and improve ventilation around the unit. Also check the wiring of the input cables and the speaker cables. After doing this, plug the power supply cord back in and turn the unit’s power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center.
Mounting the speaker stand and bracket
b Be sure to tighten the screws completely. b Also be careful when installing.
Screws
(included)
Speaker Stand 
(included)
Wall
Stick the cushion pad here. (Included)
b When placing the speaker system
(Refer to the illustration above.)
10