Desa CHDV34(N/P)(A) Optional Remote Operation, Thermostat Control Operation, CGHRC Operation

OWNER’S MANUAL

OPERATING

FIREPLACE

Continued

OPTIONAL REMOTE

OPERATION

Note: All remote control accessories must be purchased separately (see Accessories, page 36). Follow instructions included with the remote control.

Thermostat Control Operation

(Optional CGHRCT Only) The thermo- stat control setting on the remote control unit can be set to any comfort level be- tween HI and LO. The burners will turn on and off automatically to maintain the comfort level you select. The ideal com- fort setting will vary by household de- pending upon the amount of space to be heated, the output of the central heating system, etc.

For wall thermostat operation, follow in- struction supplied with thermostat acces- sory GWMT1.

CGHRC Operation:

2a. Press the ON/OFF button to turn the burner on and off. When turning burner off, the pilot will remain lit.

CGHRCT Operation:

2b. Select the MAN (manual) or AUTO button on the hand-held remote con- trol unit (see Figure 55).

•In manual mode, turn burners on or off by pressing the ON or OFF buttons on the hand-held remote control unit.

•In auto mode, the room tempera- ture is controlled by the thermo- stat in the hand-held remote con- trol unit. To increase the room tem- perature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom ar- row of the TEMP button. At higher settings the heater will run more.

Blower Control Knob	Flame
(Optional Accessory)	Adjustment
	Knob

IMPORTANT: This remote control has been specially engineered to take an air temperature sample ev- ery 5.5 minutes in the AUTO mode. It will not respond immedi- ately to the temperature setting being turned up or down.

IMPORTANT: The hand-held re- mote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off.

3. Use the STATUS button on the hand-

held remote control unit to see the

operation mode being used and the

temperature setting selected. A red

light will come on beside the opera-

tion mode being used when the sta-

tus button is pressed.

4. To turn the burners off when operat-

ing in the manual mode, press the OFF

button. If operating in the auto mode,

press the MAN button, then press the

OFF button. The pilot will remain lit.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions on page 24.

1. After lighting, let pilot flame burn for

about one minute. Turn control knob

OFF

ON

ON

OFF

REMOTE

Selector Switch in Remote Position

N		L
O		O	I
T	F	O	H
O
	F
LIP

Control Knob in ON Position

IMPORTANT: To turn the pilot off,

manually turn the control knob on the

heater to the OFF position.

to ON position. Adjust flame adjust-

ment knob anywhere between HI

and LO. Slide the selector switch to

the REMOTE position (see Figure

54). Note: The burners may light if

Figure 54 - Setting the (CGHRCT) Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

hand-held remote ON button was on

when selector switch was last turned

off. You can now turn the burners on

and off with the hand-held remote

control unit.

IMPORTANT: Do not leave the selec-

tor switch in the REMOTE position

when the pilot is not lit. This will

drain the battery.

IMPORTANT: Be sure to press the

ON/OFF buttons on the hand-held

remote control unit for up to 3 sec-

Shows Temperature Setting

Allows Burner(s) to be Turned On and Off with the Hand- Held Remote Unit.

The Heater Will Automatically Cycle Between Pilot and the Heat Setting that has been Selected.

HI

TEMP

MAN LO ON

AUTO OFF

STATUS

Increases Room Temperature

Decreases Room Temperature

Turns Burners On and Off

Shows Current Operation Mode

onds to assure proper operation.

Figure 55 - Hand-Held Thermostat Remote Control Unit Selections (CGHRCT)

Continued

105456 25