Desa LFP33PRA Installation, Check GAS Type, Electrical Hookup, Optional GA3750 Blower Accessory

OWNER’S MANUAL

INSTALLATION

NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your pri- mary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.

WARNING: A qualified ser- vice person must install fireplace. Follow all local codes.

WARNING: Never install the fireplace

Use the dimensions shown for rough open- ings to create the easiest installation (see Built-In Fireplace Installation, page 9).

IMPORTANT: Vent-free heaters add mois- ture to the air. Although this is beneficial, installing fireplace in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Com- bustion and Ventilation, pages 4 through 6.

IMPORTANT: Make sure the fireplace is level. If fireplace is not level, log set will not work properly.

CHECK GAS TYPE

Use only propane/LP gas. If your gas supply is not propane/LP gas, do not install fire- place. Call dealer where you bought fire- place for proper type fireplace.

ELECTRICAL HOOKUP

(Optional GA3750 Blower Accessory )

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other side.

8.Tighten trim hanging screws (#10 x 6.25 shoulder) into holes in cabinets. Place the assembled trim onto fireplace cabinet. Align hanging notches on trim with hanging screws on side of fire- place (see Figure 6). Push trim firmly into place, sliding hanging notches over hanging screws.

Set Screws

Side Brass	Top
	Brass
Trim
	Trim
Adjusting
Plate

• in a bedroom or bathroom
•	in a recreational vehicle
•	where curtains, furniture,

This fireplace accepts a blower assembly with an electrical cord. The electrical cord is five feet in length. You must locate fireplace within reach of a 120 volt grounded electrical

Slot

Shim

Slot

Mitered Edge

clothing, or other flammable

objects are less than 42 inches

from the front, top, or sides of

the fireplace

outlet. If not, you must install an electrical outlet within reach of fireplace power cord.

Figure 5 - Assembling Brass Trim

• in high traffic areas

• in windy or drafty areas

CAUTION: This fireplace cre- ates warm air currents. These cur- rents move heat to wall surfaces next to fireplace. Installing fire- place next to vinyl or cloth wall coverings or operating fireplace where impurities (such as to- bacco smoke, aromatic candles, cleaning fluids, oil or kerosene lamps, etc.) in the air exist, may discolor walls.

Note: Your Comfort Glow fireplace is designed to be used in zero clearance instal- lations. Wall or framing material can be placed directly against any exterior surface on the rear, sides, or top of your fireplace, except where standoff spacers are integrally attached. If standoff spacers are attached to your fireplace, these spacers can be placed directly against wall or framing materials.

ASSEMBLING AND ATTACHING OPTIONAL BRASS TRIM (Included with Mantel Accessory)

IMPORTANT: If you are recessing the fire- box in a wall, do not attach brass trim at this time. See page 9.

Note: The instructions below show assem- bling and attaching brass trim to fireplace.

1.Remove packaging from three pieces of brass trim.

2.Locate four brass screws, two adjust- ing plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 5.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 5).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 5).

Trim

Hanging

Screws

Hanging Notches on Trim

Assembled

Brass Trim

Figure 6 - Attaching Brass Trim to Fireplace

Continued

107064 7