Desa LFP33PRA Optional Remote Operation, To Turn OFF GAS To Appliance, Optional Blower Operation

OWNER’S MANUAL

OPERATING

FIREPLACE

Continued

WARNING: Make sure the se- lector switch is in the OFF posi-

OPTIONAL REMOTE

OPERATION

Note: The receiver and hand held remote control must be purchased separately (see Accessories, pages 24 and 25). Follow instructionsincludedwiththeremotecontrol.

IMPORTANT: The thermostat is built into the hand-held remote. The remote should be kept several feet from the fire- place and should be pointed towards the fireplace. If placed too close to the fire- place, the remote will sense the room is too hot and turn the fireplace off.

tion when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position.

Pilot Burner	Ignitor
	Electrode

Figure 38- Pilot

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Heater

1.Turn control knob clockwise to the OFF position.

2a. Set selector switch in the OFF position.

2b. If Using Optional Hand-Held Re- mote: Set selector switch in the OFF position to keep from draining the battery.

Shutting Off Burners Only (pilot stays lit)

You may shut off the burners and keep the pilot lit by doing one of the following:

•	Turn control knob clockwise
	to the PILOT position.
•	Use remote control manual OFF button.

Thermostat Control Operation

The thermostat control setting on the remote control unit can be set to any comfort level between HI and LO. The burners will turn on and off automati- cally to maintain the comfort level you select. The ideal comfort setting will vary by household depending upon the amount of space to be heated, the output of the central heating system, etc.

NOTICE: You must light the pilot before using the hand-held re- mote control unit. See Lighting Instructions on page 16.

After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE posi- tion. Note: The burners may light if hand- held remote ON button was on when selector switch was last turned off. You can now turn the burners on and off with the hand-held remote control unit. Follow instructions supplied with the remote con- trol for additional features.

IMPORTANT: Do not leave the selector switch in the REMOTE position when the pilot is not lit. This will drain the battery.

IMPORTANT: Be sure to press the ON/ OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

OPTIONAL BLOWER

OPERATION

Locate the blower switch by opening lower louver on fireplace. Blower switch is lo- cated at lower right inside louver door.

The GA3650TA Series thermostat-con- trolled blower has a variable speed con- trol with an ON/OFF switch. The blower will start when the thermostat senses a sufficient increase in firebox temperature. The GA3750 Series variable speed blower also has an ON/OFF switch built into the variable speed control.

Note for GA3650TA Series Only: If you are using GA3650TA blower, your fireplace and blower will not turn on and off at the same time. The fireplace may run for several minutes before the blower turns on. After the heater modulates to the pilot position, the blower will con- tinue to run. The blower will shut off after the firebox temperature decreases.

Note: It is safe to operate fireplace with blowerturnedoff.However,theblowerhelps distribute heated air from the fireplace.

Follow installation instructions included with the blower accessory.

• Set selector switch in the OFF position.

MANUAL LIGHTING

PROCEDURE

1.Follow steps 1 through 6 under Light- ing Instructions, page 16.

2.Depress control knob and light pilot with match.

3.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Now follow step 9, column 3, page 16.

	Flame Adjustment Knob
	IH		P
		F	IL
				O
		F		T
		O
				O
				N		ON
	LO					OFF
						REMOTE
	Control Knob in				Selector Switch in Remote
	On Position
					Position(Optional Remote Control)
Figure 39 - Setting the Selector Switch, Control Knob, and Flame
Adjustment Knob for Remote Operation							Continued

107064 17