![](/images/new-backgrounds/1315121/31512135x1.webp)
TABLE 1 COMPOUND MITER CUT (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE)
English |
| 5 | 10 | 15 |
|
|
|
|
|
|
|
|
|
|
|
| 20 |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
| 25 |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 30 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 35 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
| SQUARE |
|
|
| ||
|
|
|
|
|
|
|
|
| 40 |
|
|
| ||
SAW |
|
|
|
|
|
|
|
| 45 |
|
|
| ||
|
|
|
|
|
|
|
|
| 50 | BOX |
|
| A) | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| 55 |
|
|
|
| 5 | 10 | 15 |
|
|
|
|
|
|
|
| • |
| 26.5˚ |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||
SET THIS MITERANGLEON |
|
|
| 20 | 25 |
|
|
|
|
| 60 |
| ANGLE OF SIDE OF(ANGLEBOX | |
|
|
|
|
|
| 6 |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| 30 | - |
|
|
|
|
| |||
|
|
|
|
| SIDED |
|
|
|
| |||||
|
|
|
|
|
| 35 |
|
| 65 |
| ||||
|
|
|
|
|
| 40 |
|
|
| |||||
5 | 10 15 |
|
|
|
|
| BOX |
|
|
|
| |||
|
|
|
| 8 | 45 |
|
|
|
| |||||
|
| 20 | 25 |
|
| - |
|
|
|
|
| |||
|
|
|
| SIDED | 50 |
|
|
|
| 70 | ||||
SETTING |
|
| 30 | 35 |
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
| BOX | 55 |
|
|
|
| |||||
|
|
|
| 40 |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
| 45 |
| 60 |
|
|
| 75 | |||
|
|
|
|
| 50 |
|
|
|
|
| ||||
|
|
|
|
|
| 65 |
|
|
|
| ||||
|
|
|
|
| 55 |
|
|
|
|
| ||||
| DEGREE |
|
|
|
|
| 60 |
| 70 |
|
|
|
| 80 |
|
|
|
|
|
| 65 |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 70 | 75 |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| MITER |
|
|
|
|
| 75 | 80 |
|
|
|
| 85 | |
|
|
|
|
|
|
| 80 |
|
|
|
|
| ||
|
|
|
|
|
|
| 85 |
|
|
|
|
| ||
|
|
|
|
|
|
| 85 |
|
|
|
|
| ||
| BEVEL DEGREE SETTING |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| 38˚ |
|
|
SET THIS BEVEL ANGLE ON SAW
INSTRUCTIONS FOR CUTTING CROWN MOLD- ING LAYING FLAT AND USING THE COMPOUND FEATURES
1.Molding laying with broad back surface down flat on saw table (See Figure 30)
2.The settings below are for All Standard (U.S.) crown molding with 52° and 38° angles.
BEVEL | TYPE OF CUT | |
SETTING | LEFT SIDE,INSIDE CORNER: | |
| ||
Left 33.9° | 1. | Top of molding against fence |
| 2. | Miter table set right 31.62° |
| 3. | Save left end of cut |
RIGHT SIDE, INSIDE CORNER: Right 33.9° 1. Top of molding against fence
2.Miter table set left 31.62°
3.Save right end of cut
LEFT SIDE, OUTSIDE CORNER: Right 33.9° 1. Top of molding against fence
2.Miter table set left 31.62°
3.Save left end of cut
RIGHT SIDE, OUTSIDE CORNER:
Left 33.9° 1. Top of molding against fence
2.Miter table set right 31.62°
3.Save right end of cut
When setting bevel and miter angles for all compound miters, remember that:
The angles presented for crown moldings are very precise and difficult to set exactly. Since they can easily shift slightly and very few rooms have exactly square corners, all settings should be tested on scrap molding.
PRETESTING WITH SCRAP MATERIAL IS
EXTREMELY IMPORTANT!
14