DKS Enterprises 9310 2.4 Auxiliary Device Wiring

2.4 Auxiliary Device Wiring

1234567891011121314

15 16 17 18

4403-010

Circuit Board

Secondary Entrapment

Protection Inputs

DOORKING, INC., INGLEWOOD, CA 90301

Title:

Date: Rev.Dwg. No.

N.O.

N.C.

COM

N.O.

N.C.

COM

Green

Red

White

2351-010

Circuit Board

DoorKing 1404-080

Remote Reset Switch

DoorKing 2351-010

Tracker Expansion Board

Auxiliary Stop Using Magnetic Switch

Normal

Operation

Operator

Stopped

1

2

The auxiliary stop switch will stop a moving gate when activated or will prevent the gate operator from starting when activated. Note that

this input is normally open and that a switch closure is required to activate the stop function. Because of this, the auxiliary stop

shown must NEVER be used as a safety interlock device.

Jumper is placed across terminals 8 and 9 ONLY WHEN THE AUXILIARY STOP INPUT IS USED.

The Remote Alarm Reset Station MUST be mounted in the line-of-sight of the gate operator.

Using a 2351-010 Tracker Expansion Board, operator data can be sent to the access co ntroller (DoorKing 1833, 1835, 1837 or 1838 only).

Refer to Installation Manual 2351-065 for detailed information.

1

2

3

4

3

4

5/07 A

4403-AUXDEV-1

Model 9310

Auxiliary Device Wiring Diagram

19 20

CAUTION

High Voltage

Open Photo

Close Photo

Open Edge

Close Edge

Common

Common

9310-065-E-5-07 Page 29

Contents

Main Owners Manual Page Use this manual with the following models only. QUICK START 9410 REVERSE LOOP EXIT LOOP ON 123 1 DIRECTION 2 TIMER 9310-065-E-5-07 Page 5 Secondary Entrapment Protection Devices 3-Wire Receiver 4-Wire Receiver Glossary Entrapment Protection Important Notices Important Safety Instructions Gate Construction Instructions regarding intended installation: Page Slide Gate Requirements B Page 12 9310-065-E-5-07 B Slide Gate Protection Table of Contents Section 1 Installation Section 2 Wiring Section 3 Adjustments Section 4 Operating Instructions Section 5 Maintenance and Troubleshooting Page SECTION 1 - INSTALLATION 1.1 Specifications 1.2 Concrete Pad 1.3 Operator Installation 90 NO! 1.4 Chain Installation NO! Page 1.6 Rear Mount 1.7 Warning Sign Installation WARNING Moving Gate Can Cause Serious Injury or Death Page SECTION 2 WIRING 2.1 High Voltage Connections 2.2 Control Wiring A B C D 2.3 Loop Detectors Detail A Reverse Exit 2.4 Auxiliary Device Wiring 2.5 Primary Secondary (Bi-parting) Gate Wiring D E Operator 4403-010 Circuit Board 2.6 Terminal Identification and Description 2.6.1 Main Terminal (P1) 2.6.2 Secondary Device Terminal (P3) SECTION 3 - ADJUSTMENTS 9310-065-E-5-07 Page 33 SW1 SW2 3.1 Circuit Board Adjustments Set the DIP-switches on the circuit board to the desired setting. See switch-setting charts in 3.2 Switch Settings SWITCH FUNCTION SETTING DESCRIPTION SW 2 (LOWER SWITCH) SWITCH FUNCTION SETTING DESCRIPTION 3.2.1 Programming Switch Description and Function 3.3 Limit Switch Adjustments Slide to Adjust Partial Open Limit 3.4 Reverse Sensitivity Adjustment REVERSE SENSOR MIN MAX MIN MAX CLOSE OPEN Page SECTION 4 OPERATING INSTRUCTIONS 4.1 Power and Reset Switches 4.2 Shutdown Conditions 4.2.1 Soft Shutdown 4.2.2 Resetting a Soft Shutdown 4.2.3 Hard Shutdown 4.2.4 Resetting a Hard Shutdown 4.3 Manual Gate Operation 4.3.1 Emergency Vehicle Access Conditions 4.3.2 Fail-Safe Manual Operation 4.3.3 Fail-Secure Manual Operation 1/4 TURN Page SECTION 5 MAINTENANCE AND TROUBLESHOOTING 5.1 Maintenance 5.2 Operator Diagnostics 5.3 Trouble Shooting Page 5.4 Accessories 115 VAC 208/230/460 V 230V 460V For 3 Phase power input, use 2 power legs and cap the third. 115 VAC 230V 208/230 V Single Phase 208/230/460 V Three Phase 208/230 460 230 V 460 V Motor 1 HP