DKS Enterprises 9310 Use this manual with the following models only.

Use this manual with the following models only.

All 9310 models with circuit board 4403-010. IMPORTANT! The 4403 circuit board used in the

model 9310 IS NOT interchangeable with the 4402 circuit board used in the earlier model

9300 operators.

NOTE: Models 9310-081, 9310-083, 9310-085, 9310-087, 9310-089, 9310-091, 9310-093, 9310-

095 and 9310-097 will have a supplemental manual (P/N 2340-065) that describes the operation

and setup of the optional battery backup system available with this unit, and provides additional

wiring information for this unit.

DoorKing, Inc. reserves the right to make changes in the products described in this manual

without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions

or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to

this manual. This manual is copyrighted, all rights reserved. No portion of this manual may be

copied, reproduced, translated, or reduced to any electronic medium without prior written consent

from DoorKing, Inc.

9310-065-E-5-07 Page 3

Contents

Main Owners Manual Page Use this manual with the following models only. QUICK START 9410 REVERSE LOOP EXIT LOOP ON 123 1 DIRECTION 2 TIMER 9310-065-E-5-07 Page 5 Secondary Entrapment Protection Devices 3-Wire Receiver 4-Wire Receiver Glossary Entrapment Protection Important Notices Important Safety Instructions Gate Construction Instructions regarding intended installation: Page Slide Gate Requirements B Page 12 9310-065-E-5-07 B Slide Gate Protection Table of Contents Section 1 Installation Section 2 Wiring Section 3 Adjustments Section 4 Operating Instructions Section 5 Maintenance and Troubleshooting Page SECTION 1 - INSTALLATION 1.1 Specifications 1.2 Concrete Pad 1.3 Operator Installation 90 NO! 1.4 Chain Installation NO! Page 1.6 Rear Mount 1.7 Warning Sign Installation WARNING Moving Gate Can Cause Serious Injury or Death Page SECTION 2 WIRING 2.1 High Voltage Connections 2.2 Control Wiring A B C D 2.3 Loop Detectors Detail A Reverse Exit 2.4 Auxiliary Device Wiring 2.5 Primary Secondary (Bi-parting) Gate Wiring D E Operator 4403-010 Circuit Board 2.6 Terminal Identification and Description 2.6.1 Main Terminal (P1) 2.6.2 Secondary Device Terminal (P3) SECTION 3 - ADJUSTMENTS 9310-065-E-5-07 Page 33 SW1 SW2 3.1 Circuit Board Adjustments Set the DIP-switches on the circuit board to the desired setting. See switch-setting charts in 3.2 Switch Settings SWITCH FUNCTION SETTING DESCRIPTION SW 2 (LOWER SWITCH) SWITCH FUNCTION SETTING DESCRIPTION 3.2.1 Programming Switch Description and Function 3.3 Limit Switch Adjustments Slide to Adjust Partial Open Limit 3.4 Reverse Sensitivity Adjustment REVERSE SENSOR MIN MAX MIN MAX CLOSE OPEN Page SECTION 4 OPERATING INSTRUCTIONS 4.1 Power and Reset Switches 4.2 Shutdown Conditions 4.2.1 Soft Shutdown 4.2.2 Resetting a Soft Shutdown 4.2.3 Hard Shutdown 4.2.4 Resetting a Hard Shutdown 4.3 Manual Gate Operation 4.3.1 Emergency Vehicle Access Conditions 4.3.2 Fail-Safe Manual Operation 4.3.3 Fail-Secure Manual Operation 1/4 TURN Page SECTION 5 MAINTENANCE AND TROUBLESHOOTING 5.1 Maintenance 5.2 Operator Diagnostics 5.3 Trouble Shooting Page 5.4 Accessories 115 VAC 208/230/460 V 230V 460V For 3 Phase power input, use 2 power legs and cap the third. 115 VAC 230V 208/230 V Single Phase 208/230/460 V Three Phase 208/230 460 230 V 460 V Motor 1 HP