DKS Enterprises 9310 SECTION 4 OPERATING INSTRUCTIONS

SECTION 4 – OPERATING INSTRUCTIONS

WARNING - To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Never let children operate or play with gate controls. Keep the remote control away

from children.

3. Always keep people and objects away from gate. NO ONE SHOULD CROSS THE

PATH OF THE MOVING GATE

4. Test the operator monthly. The gate MUST reverse on contact with a rigid object or

stop or reverse when an object activates the non-contact sensors. After adjusting the

force or the limit of travel, retest the gate operator. Failure to adjust and retest the

gate operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving and power has been

shut-off.

6. KEEP GATES PROPERLY MAINTAINED. Read the owner's manual. Have a

qualified service person make repairs to gate hardware.

7. The entrance is for vehicles only. Pedestrians must use separate entrance.

8. SAVE THESE INSTRUCTIONS.

4.1 Power and Reset Switches

Open the power switch cover located on the side of the operator to access the MAIN POWER switch

and the operator RESET switch.

The RESET switch is used to turn off the entrapment

alarm and to reset the operator after a hard shutdown

has occurred.

OFF

AC

POWER

RESET

The AC POWER toggle switch turns power to the

operator ON (toggle up) or OFF (toggle down).

The DC POWER toggle switch (units equipped with

the backup option only) turns power to the DC backup

system ON (toggle up) or OFF (toggle down).

9310-065-E-5-07 Page 39

Contents

Main Owners Manual Page Use this manual with the following models only. QUICK START 9410 REVERSE LOOP EXIT LOOP ON 123 1 DIRECTION 2 TIMER 9310-065-E-5-07 Page 5 Secondary Entrapment Protection Devices 3-Wire Receiver 4-Wire Receiver Glossary Entrapment Protection Important Notices Important Safety Instructions Gate Construction Instructions regarding intended installation: Page Slide Gate Requirements B Page 12 9310-065-E-5-07 B Slide Gate Protection Table of Contents Section 1 Installation Section 2 Wiring Section 3 Adjustments Section 4 Operating Instructions Section 5 Maintenance and Troubleshooting Page SECTION 1 - INSTALLATION 1.1 Specifications 1.2 Concrete Pad 1.3 Operator Installation 90 NO! 1.4 Chain Installation NO! Page 1.6 Rear Mount 1.7 Warning Sign Installation WARNING Moving Gate Can Cause Serious Injury or Death Page SECTION 2 WIRING 2.1 High Voltage Connections 2.2 Control Wiring A B C D 2.3 Loop Detectors Detail A Reverse Exit 2.4 Auxiliary Device Wiring 2.5 Primary Secondary (Bi-parting) Gate Wiring D E Operator 4403-010 Circuit Board 2.6 Terminal Identification and Description 2.6.1 Main Terminal (P1) 2.6.2 Secondary Device Terminal (P3) SECTION 3 - ADJUSTMENTS 9310-065-E-5-07 Page 33 SW1 SW2 3.1 Circuit Board Adjustments Set the DIP-switches on the circuit board to the desired setting. See switch-setting charts in 3.2 Switch Settings SWITCH FUNCTION SETTING DESCRIPTION SW 2 (LOWER SWITCH) SWITCH FUNCTION SETTING DESCRIPTION 3.2.1 Programming Switch Description and Function 3.3 Limit Switch Adjustments Slide to Adjust Partial Open Limit 3.4 Reverse Sensitivity Adjustment REVERSE SENSOR MIN MAX MIN MAX CLOSE OPEN Page SECTION 4 OPERATING INSTRUCTIONS 4.1 Power and Reset Switches 4.2 Shutdown Conditions 4.2.1 Soft Shutdown 4.2.2 Resetting a Soft Shutdown 4.2.3 Hard Shutdown 4.2.4 Resetting a Hard Shutdown 4.3 Manual Gate Operation 4.3.1 Emergency Vehicle Access Conditions 4.3.2 Fail-Safe Manual Operation 4.3.3 Fail-Secure Manual Operation 1/4 TURN Page SECTION 5 MAINTENANCE AND TROUBLESHOOTING 5.1 Maintenance 5.2 Operator Diagnostics 5.3 Trouble Shooting Page 5.4 Accessories 115 VAC 208/230/460 V 230V 460V For 3 Phase power input, use 2 power legs and cap the third. 115 VAC 230V 208/230 V Single Phase 208/230/460 V Three Phase 208/230 460 230 V 460 V Motor 1 HP