Dynacord Professional Power Amplifiers manual technical specifications, PowerH Series, General

PowerH Series

PowerH 5000

PowerH Series

technical specifications

General			H 2500				H 5000
Load Impedance	2 Ω		4 Ω		8 Ω	2 Ω	4 Ω	8 Ω
Maximum Midband Output Power, 1 kHz, THD=1%	2000 W		1450 W		850 W	3500 W	2500 W	1500 W
Rated Output Power, 20 Hz ... 20 kHz, THD <0.1%	-		1200 W		600 W	-	2100 W	1050 W
Max. Single Channel Output Power Dynamic-Headroom,IHF-A	2400 W		1700 W		940 W	4500 W	3200 W	1800 W
Max. Single Channel Output Power Continuous, 1kHz	2050 W		1600 W		900 W	4100 W	2700 W	1600 W
Maximum Bridged Output Power 1 kHz, THD=1%	-		3800 W		2900 W	-	7000 W	5000 W
Maximum RMS Voltage Swing 1 kHz, THD=1%			95 V				125 V
Power Bandwidth, THD=1%, ref. 1kHz, half power @ 4Ω					10 Hz ... 50 kHz
Voltage Gain ref. 1 kHz	39 dB / 35 dB / 32 dB (switchable)					41dB / 35 dB / 32 dB (switchable)
Input Sensitivity at rated output power @ 8Ω, 1 kHz	0 dBu / +4 dBu / +7 dBu (switchable)					0 dBu / +6 dBu / +9 dBu (switchable)
THD at rated output power MBW=80kHz, 1 kHz				< 0.05 %
IMD-SMPTE,60 Hz, 7 kHz				< 0.05 %
DIM 30, 3.15 kHz, 15 kHz				< 0.02 %
Max. Input Level					+22 dBu (9,76 Vrms)
Crosstalk, ref. 1 kHz at rated output power					< -80 dB
Frequency Response, ref. 1 kHz					< 10 Hz ... 30 kHz (± 1dB)
Input Inpedance, active balanced					20 kΩ
Damping Factor ,1kHz				> 400
Slew Rate			30 V/µs				35V/µs
Signal to Noise Ratio Amplifier A-weighted, 32 dB constant gain			109 dB				111 dB
Output Noise , A-weighted					< -70 dBu
Output Stage Topology					Class-H Grounded Bridge
Power Requirements			100 V - 240 V, 50 Hz - 60 Hz; 100 V, 50 Hz - 60 Hz
Power Consumption at 1/8 maximum output power @ 4 Ω			1000 W				1450 W
Protections	Audio limiters, High temperature, DC, HF, Short Circuit, Back-EMF, Peak current
	limiters, Inrush current limiters,Turn-on Delay, Mains Circuit Breaker Protection,
			Mains Over / Undervoltage Protection
Cooling					Front-to-Rear, 5-stage-fans
Ambient Temperature Limits				+5°C ... +40°C (40°F ... 105°F)
Safety Class						I
Dimensions (WxHxD), mm					483 x 88.1 x 498
Weight		14.2 kg (31.1 lbs)				14.5 kg (32.0 lbs)
Amplifier at rated conditions, both channels driven with 8 Ω loads, unless otherwise specified

55