Intelligent Technologies (IT.) D77A I/O Module Products
Configuration Parameters
None of the Configuration Parameters support I/O data.
Table 43: 0x8001 (32769) Device Identity
Size | Description |
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
14 bytes | This | ||||||
| Product Code |
|
| A device’s unique product code must be reported. Each | |||
| (2 bytes) |
|
| vendor must maintain its own list of product codes. | |||
| Vendor ID |
|
| Each QCPort vendor must use their unique ID as assigned | |||
| (2 bytes) |
|
| by Eaton Electrical. | |||
| Serial Number |
|
| A device’s serial number must be reported. This value must | |||
| (4 bytes) |
|
| be unique for a particular manufacturer across all device | |||
|
|
|
|
| types. |
|
|
| Hardware Revision |
|
| Major revision must be reported in the MSB. Minor revision | |||
| (2 bytes) |
|
| must be reported in the LSB. | |||
| Firmware Revision |
|
| Major revision must be reported in the MSB. Minor revision | |||
| (2 bytes) |
|
| must be reported in the LSB. | |||
| QCPort Revision |
|
| Major revision must be reported in the MSB. Minor revision | |||
| (2 bytes) |
|
| must be reported in the LSB. | |||
|
|
|
|
|
|
| |
Table 44: 0x8002 (32770) Configuration CRC |
|
|
| ||||
|
|
|
|
|
|
| |
Size |
| Description |
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
2 bytes |
| Used for confirmation of a device’s configuration. Normally, the initial values of selected configuration | |||||
|
| parameters would be included in the calculation. The product instruction leaflet should describe which | |||||
|
| parameters are actually included. To facilitate node replacement, Device Identity information should not be | |||||
|
| included in this calculation. |
|
|
| ||
|
|
|
|
|
|
| |
Table 45: 0x8003 (32771) Node ID |
|
|
|
|
| ||
|
|
|
|
|
|
| |
Size |
| Description |
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
2 bytes |
| This parameter specifies a device’s Node ID. The Group ID is the Most Significant Byte and the Member ID is the | |||||
|
| Least Significant Byte. |
|
|
| ||
|
| An Initial Value of 0x0000 indicates an unconfigured state. In this state, a device assumes a current value based | |||||
|
| on the level of switch support implemented in hardware. |
|
| |||
|
|
|
|
|
|
| |
Table 46: 0x8004 (32772) Operating Mode |
|
|
|
|
| ||
|
|
|
|
|
|
| |
Size |
| Description |
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
1 byte |
| This parameter specifies a device’s operating mode, as follows: | |||||
|
|
|
|
|
|
|
|
|
|
|
| Mode | Description | Active/Passive |
|
|
|
|
|
|
|
|
|
|
|
|
| 0x00 | Unconfigured | Passive |
|
|
|
|
| 0x01 | Simple System | Passive |
|
|
|
|
| 0x02 | Master/Slave | Active |
|
|
|
|
| 0x03 | Wire Replacer | Passive |
|
|
|
|
| 0x04 | Faulted | Passive |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
Table 47: 0x8005 (32773) QCPort Baud Rate |
|
|
|
|
| ||
|
|
|
|
|
|
| |
Size |
| Description |
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
1 byte |
| This parameter specifies the QCPort baud rate for a device as indicated below: | |||||
|
| 0x00 — | 9,600 |
|
|
|
|
|
| 0x01 — | 19,200 |
|
|
|
|
|
| 0x02 — | 38,400 |
|
|
|
|
|
| 0x03 — | 57,600 |
|
|
|
|
|
| 0x04 — 115,200 |
|
|
| ||
|
| 0x05 — 230,400 |
|
|
| ||
|
| 0x06 — 460,800 |
|
|
| ||
|
| Note that the current value of the baud rate cannot be directly modified. The current value is set to the initial | |||||
|
| value upon reset. Therefore, writing to the initial value and resetting the device sets a new current value. | |||||
|
|
|
|
|
|
|
|
50 | For more information visit: www.EatonElectrical.com | MN05002001E |
