Eaton Electrical V3

www.eaton.com

Network Shutdown Module V3 – User Manual - 34 003 934 XU / AE Page 20/65

z Battery: Charging / Discharging / Battery fault.

z Output: Main output status (ON/OFF/Internal Failure/On Automatic

Bypass/Manual By Pass/Overload).

Or output outlet status (ON/OFF).

The outlet group that powers the device is highlighted in bold

Values

z Output Load Level: The output load level of the device.

z Battery capacity: Battery capacity of the device.

z Backup time: The device remaining backup time.

Note that this view is impacted when any device status is affected.

Contents

Main Network Shutdown Module V3 Table of Contents Page 1 Introduction to the EATONs Network Solution 1.1 Overview 1.2 Monitoring the UPSs over the network 1.3 Protecting the computers / servers New functions: 1.4 Connecting the UPS 1.4.1 Connecting to the Network 1.4.2 Select Network Architecture 1.4.3 Network Performances 2 Installation 2.1 Hardware Pre-requisites (Electrical and Network Connections) 2.2 Software Installation Pre-requisites 2.2.1 On the System Hosting Network Shutdown Module V3 2.2.1.1 Windows Compatibilities: 2.2.1.2 Linux Compatibilities: 2.2.1.3 Mac Compatibilities: 2.2.1.4 Standby configuration (Windows): 2.2.1.5 Broadcast Message configuration (Windows): 2.2.1.6 Firewall configuration (Windows & Linux) and Gateway : 2.2.2 On the System that Displays Web-based Graphical User Interface 2.3 Quick Start 2.4 Software Installation Procedure Page 2.5 Application deployment and silent installation (advanced) 2.6 Uninstalling the Network Shutdown Module 3 Minimal configuration steps 3.1 Introduction 3.2 The IP address of the UPS that powers your server. Page 3.3 Users accounts configuration 4 Use 4.1 Monitoring the server and the UPS(s) 4.1.1 Local access 4.1.2 Remote access Page Page 4.2 System and UPS event log 4.3 UPS Events list Page 4.4 Test the communication with the UPS 4.4.1 Simple Tests 4.4.2 Advanced tests Messages in verbose mode: 4.5 Start and stop the Shutdown Module (advanced) 5 Other Configuration possibilities 5.1 Introduction 5.2 Configure system parameters 5.3 Shutdown Configuration Page 5.4 Checking for Upgrades 5.5 Events and actions (advanced configuration) Page 6 Multi-UPS Systems 6.1 Caution 6.2 Presentation Page Page 6.3 Create a multi-UPS configuration 7 Appendix 7.1 Single UPS Mode compatibility 7.1.1 Card/Proxy compatibility 7.1.2 UPSs compatibility 7.2 Multi-UPS Mode Compatibility list Page 7.2.3 Simple associations of the previous configurations 7.2.4 Configurations NOT supported 7.3 Examples of Multi UPS configurations 7.4 Multi-UPS Systems and Event Management 7.5 Application deployment and silent installation 7.5.1 Introduction 7.5.2 Customized installation package 7.5.3 Install the Shutdown Module in silent mode 7.5.4 Advanced installation options 7.6 Single UPS Shutdown Sequence 1 2 3 4 5 6 Page 7.7 Multi UPS shutdown sequence (example with Static Transfer Switch) 1 2 3 4 5 6 7.8 Additional information on events and actions 7.8.1 Action settings Tab 7.8.1.1 The different actions 7.8.1.2 Add an action 7.8.1.3 System Shutdown Action Page 7.8.1.4 Execute Action 7.8.1.5 Send email Action 7.8.2 Events Tab 7.8.2.1 Notification alarms 7.8.2.2 Protection alarms 7.8.2.3 Multi UPS Systems and Notification Alarms 7.8.2.4 Multi UPS Systems and Protection Alarms 7.8.3 Test tab 7.8.4 The action parameters (execute and send email) 7.8.5 Software utilities 7.8.5.1 Shutdown.bat (Windows Script) 7.8.5.2 Shutdown.sh (Linux Script) 7.8.5.3 Wait (Windows) 7.8.5.4 Windows RunAs command or legacy mgeRunAs software utility Page 7.9 FAQ and Error messages Page Page 8 Glossary Shutdown Duration Shutdown Timer www.eaton.com 9 Acknowledgements 9.1 SQLite 9.2 Pi3Web 9.3 PHP 9.4 OpenSSL Huge thanks from the EATON software development team to the OpenSSL Project. Page www.eaton.com 9.5 Lighttpd Huge thanks from the EATON software development team to the Lighttpd Project. 9.6 WxWidget Huge thanks from the EATON software development team to the WxWidget Project.