Eaton Electrical V3 7.2.4 Configurations NOT supported

www.eaton.com

Network Shutdown Module V3 – User Manual - 34 003 934 XU / AE Page 37/65

7.2.4 Configurations NOT supported

z This configuration with STS in cascade is NOT

supported by NSM V3

z This configuration with a load derived between the 2

UPSs in serial redundancy is NOT supported by

NSM V3

z This configuration with a mix of “Parallel” and “STS”

is NOT supported by NSM V3

z The following configuration is NOT supported,

because it is NOT symmetrical on both STS inputs

Contents

Main Network Shutdown Module V3 Table of Contents Page 1 Introduction to the EATONs Network Solution 1.1 Overview 1.2 Monitoring the UPSs over the network 1.3 Protecting the computers / servers New functions: 1.4 Connecting the UPS 1.4.1 Connecting to the Network 1.4.2 Select Network Architecture 1.4.3 Network Performances 2 Installation 2.1 Hardware Pre-requisites (Electrical and Network Connections) 2.2 Software Installation Pre-requisites 2.2.1 On the System Hosting Network Shutdown Module V3 2.2.1.1 Windows Compatibilities: 2.2.1.2 Linux Compatibilities: 2.2.1.3 Mac Compatibilities: 2.2.1.4 Standby configuration (Windows): 2.2.1.5 Broadcast Message configuration (Windows): 2.2.1.6 Firewall configuration (Windows & Linux) and Gateway : 2.2.2 On the System that Displays Web-based Graphical User Interface 2.3 Quick Start 2.4 Software Installation Procedure Page 2.5 Application deployment and silent installation (advanced) 2.6 Uninstalling the Network Shutdown Module 3 Minimal configuration steps 3.1 Introduction 3.2 The IP address of the UPS that powers your server. Page 3.3 Users accounts configuration 4 Use 4.1 Monitoring the server and the UPS(s) 4.1.1 Local access 4.1.2 Remote access Page Page 4.2 System and UPS event log 4.3 UPS Events list Page 4.4 Test the communication with the UPS 4.4.1 Simple Tests 4.4.2 Advanced tests Messages in verbose mode: 4.5 Start and stop the Shutdown Module (advanced) 5 Other Configuration possibilities 5.1 Introduction 5.2 Configure system parameters 5.3 Shutdown Configuration Page 5.4 Checking for Upgrades 5.5 Events and actions (advanced configuration) Page 6 Multi-UPS Systems 6.1 Caution 6.2 Presentation Page Page 6.3 Create a multi-UPS configuration 7 Appendix 7.1 Single UPS Mode compatibility 7.1.1 Card/Proxy compatibility 7.1.2 UPSs compatibility 7.2 Multi-UPS Mode Compatibility list Page 7.2.3 Simple associations of the previous configurations 7.2.4 Configurations NOT supported 7.3 Examples of Multi UPS configurations 7.4 Multi-UPS Systems and Event Management 7.5 Application deployment and silent installation 7.5.1 Introduction 7.5.2 Customized installation package 7.5.3 Install the Shutdown Module in silent mode 7.5.4 Advanced installation options 7.6 Single UPS Shutdown Sequence 1 2 3 4 5 6 Page 7.7 Multi UPS shutdown sequence (example with Static Transfer Switch) 1 2 3 4 5 6 7.8 Additional information on events and actions 7.8.1 Action settings Tab 7.8.1.1 The different actions 7.8.1.2 Add an action 7.8.1.3 System Shutdown Action Page 7.8.1.4 Execute Action 7.8.1.5 Send email Action 7.8.2 Events Tab 7.8.2.1 Notification alarms 7.8.2.2 Protection alarms 7.8.2.3 Multi UPS Systems and Notification Alarms 7.8.2.4 Multi UPS Systems and Protection Alarms 7.8.3 Test tab 7.8.4 The action parameters (execute and send email) 7.8.5 Software utilities 7.8.5.1 Shutdown.bat (Windows Script) 7.8.5.2 Shutdown.sh (Linux Script) 7.8.5.3 Wait (Windows) 7.8.5.4 Windows RunAs command or legacy mgeRunAs software utility Page 7.9 FAQ and Error messages Page Page 8 Glossary Shutdown Duration Shutdown Timer www.eaton.com 9 Acknowledgements 9.1 SQLite 9.2 Pi3Web 9.3 PHP 9.4 OpenSSL Huge thanks from the EATON software development team to the OpenSSL Project. Page www.eaton.com 9.5 Lighttpd Huge thanks from the EATON software development team to the Lighttpd Project. 9.6 WxWidget Huge thanks from the EATON software development team to the WxWidget Project.