Manuals / Echo / Computer Equipment / Network Router

Echo EN55022 manual Testing, Data Connections, Front Panel LEDs, LED Label

Models: EN55022

1 59

Download 59 pages 20.16 Kb

Page 19

3.4Testing

3.4Testing

Replace the cover and screws before powering up the unit. Correct installation of the Router Option may be confirmed by the login prompt (see section 2.3) appearing on the terminal screen. If the red error LED on the front panel is on, this indicates hardware fault has occurred. In this case, disconnect the power cable and check the installation of the Router Option is correct.

3.5Data Connections

The Ethernet connection is made using either the AUI (15-way D-type – see Appendix E) or 10BASE-T (RJ45 see Appendix F) port at the rear of the unit (refer to Appendix D).

3.6Front Panel LEDs

For information regarding CARRIER, MAJOR ALARM, MINOR ALARM and LOOP, refer to the Echo LANlink User Manual.

LED Label	Notes

TX DATA	Flashes when unit is transmitting Ethernet data

RX DATA	Flashes when unit is receiving Ethernet data

COLLISION	Flashes if an Ethernet collision is detected

FAULT	RED if a power up hardware fault has occurred

Echo LANlink Router Option User Manual

Issue 1.0 04 December 1997 Page 19 of 59

Image 19

Echo EN55022 manual Testing, Data Connections, Front Panel LEDs, LED Label

Contents

Page 5SXLANlink Router Option User ManualPart Number EA88001A WARNING - BEFORE INSTALLATION, PLEASE REFER TO SAFETY INSTRUCTIONS INROUTER MENU OPTIONS CONTENTSINSTALLATION USE AND CONFIGURATIONAppendix C EMC REQUIREMENTS Appendix I ROUTER MAINTENANCE MENUAppendix A WARNINGS Appendix B APPROVAL REQUIREMENTSGLOSSARY 1 INTRODUCTION Echo LANlink Router Option User ManualFigure 1 Linking two LANs together 1.2 Typical Applications 1.1 Functional OverviewFigure 2 Restrictive Firewall Example Default terminal VT 100/220/320/420. OK y or n? 2 USE AND CONFIGURATION2.1 Router Configuration loginSupported Terminal Types returnFigure 4 Main Menu Screen 2.4.2 Parameter Selection 2.4 Router ManagementFigure 5 Router Management Screen 2.4.1 General Keyboard Conventions selects/initiates the highlighted optionIssue 1.0 04 December 1997 Page 12 of Figure 6 Entering a ParameterEcho LANlink Router Option User Manual 2.5 Multiplexer Management Figure 7 Main Multiplexer Configuration Page2.5.1 Allocating bandwidth to the Router 2.5.2 Returning to the Main Menu Screen 2.5.3 Clearing the Configuration back to Factory Default2.6 System Status Figure 8 Example Timeslot Set-up2.6.1 MAIN LINK CARRIER LOSS 2.6.3 REMOTE ALARM2.6.6 MAIN LINK HIGH BIT ERROR RATE 2.6.8 D/I REMOTE ALARMEcho LANlink Router Option User Manual 2.6.9 ROUTER WAN LINK STATUSIssue 1.0 04 December The status of the link between the two routers is displayedFigure 9 Echo LANlink Baseboard 3 INSTALLATIONWARNING - Refer to Appendix A for Safety Instructions 3.1 Opening the Multiplexer3.2 Internal Link LK13 3.3 Installing the Router OptionFigure 10 Echo LANlink showing Router Option Fitted LED Label 3.4 Testing3.5 Data Connections 3.6 Front Panel LEDs3.7.2.1 Service Name 3.7 Quick Configuration3.7.1 Multiplexer Configuration 3.7.2 Router Configuration3.7.2.6 IP Broadcast 3.7.2.8 IPX Configuration3.7.2.4 Receive IP RIP 3.7.2.5 Transmit IP RIP3.7.2.14 Transmit IPX SAP 3.7.2.11 Receive IPX RIP3.7.2.12 Transmit IPX RIP 3.7.2.13 Receive IPX SAPDESCRIPTION 4 ROUTER MENU OPTIONS4.1 UNIT STATUS PARAMETERDESCRIPTION 4.2 TRAFFIC ANALYSIS4.2.1 IP ROUTING TABLE PARAMETERPARAMETER 4.2.2 IP ARP TABLEPARAMETER DESCRIPTIONPARAMETER 4.2.3 IPX RIP TABLEDESCRIPTION PARAMETER 4.2.4 IPX SAP TABLEDESCRIPTION DESCRIPTION 4.3 NETWORK LOADING4.2.5 SHOW TRAFFIC DETAILS PARAMETERPARAMETER 4.4.2 NAME SERVER CONFIGURATION4.4 REMOTE MANAGEMENT 4.4.1 TELNET OUTDESCRIPTION 4.4.2.1 NAME TO IP CACHE4.4.3 SECURITY PARAMETERDESCRIPTION 4.5 UNIT CONFIGURATION4.4.4 SNMP SETUP PARAMETERDESCRIPTION 4.6 SERVICE SETUP4.6.1 ETHERNET SERVICE SETUP PARAMETERPacket PARAMETEROPTIONS DESCRIPTIONOPTIONS 4.6.2 WAN SERVICE SETUPPARAMETER DESCRIPTIONOPTIONS 4.6.2.1 PPP SETUPPARAMETER DESCRIPTIONDESCRIPTION 4.7 FILTER SETUP4.7.1 MAC FILTERS WAN or Ethernet MENU SELECTIONDESCRIPTION 4.7.2 IP FILTER WAN or EthernetLIST PARAMETER MENU SELECTIONDESCRIPTION 4.7.3 IPX SAP FILTER MENU WAN or EthernetNetwork Address 32 bits MENU SELECTIONLIST PARAMETER Node Address 48 bitsMENU SELECTION DESCRIPTIONLIST PARAMETER 4.7.4 IPX HEADER FILTERSMENU SELECTION DESCRIPTIONDESCRIPTION 4.8 EVENTS4.7.5 NOVELL KEEP-ALIVES MENU SELECTION4.8.2 SYSTEM EVENTS 4.8.1 PPP EVENTSEcho LANlink Router Option User Manual FLASH ERASE ERROR PARAMETERFLASH PROGRAMMING TIMEOUT FLASH VERIFY ERROR Issue 1.0 04 December 1997 Page 43 ofsafety status of which are defined below INSTALLATION OF EQUIPMENTInstallation of this equipment must only be performed by suitably trained serviceDieses Gerät Muß an einem Ansc hluß mit Installation des Gerätesv EXT CLOCK vi ALARM port vii AUI port viii 10BASE-T port Warnungi port Supervisor Mise en garde Installation de léquipmentMise en garde Cet équipement doit être relié a la terre Mise en garde Connexion dautres équipementsIssue 1.0 04 December 1997 Page 47 of APPENDIX B APPROVAL REQUIREMENTSEcho LANlink Router Option User Manual Issue 1.0 04 December 1997 Page 48 of APPENDIX C EMC REQUIREMENTSEcho LANlink Router Option User Manual Issue 1.0 04 December 1997 Page 49 of APPENDIX D REAR PANEL LAYOUTEcho LANlink Router Option User Manual +12V APPENDIX E AUI PORT 15-WAY D-TYPE PINOUTSCREEN ACX+SHELL APPENDIX F 10BASE-T RJ45 PORT PINOUTG.1 Source and Destination IP Address APPENDIX G IP FILTER EXAMPLESG.3 Source and Destination Ports G.1.1 ExamplesG.2 PROTOCOL SELECTION G.2.1 ExamplesG.3.1 Examples Unit 24 bits APPENDIX H IP SUBNETSClass A Address Network 8 bitsI.1 KERMIT APPENDIX I ROUTER MAINTENANCE MENUI.3 Download New Firmware using TFTP I.2 Download New Firmware using TCP loaderI.4 Restore Configuration using TFTP I.5 Set New IP Address I.6 Set Default GatewayI.8 Reset Password I.9 Boot File Using TCP LoaderI.11 Run Monitor I.10 Boot File Using TFTP Loader