Manuals / Eiki / Computer Equipment / Projector

Eiki LC-VC1 owner manual Configurations Of Terminals, Rgb Terminal, Serial Terminal

Models: LC-VC1

1 44

Download 44 pages 44.87 Kb

Page 43

CONFIGURATIONS OF TERMINALS

CONFIGURATIONS OF TERMINALS

RGB TERMINAL

Terminal HDB1 5-PIN

Connect the display output terminal of computer to this terminal with VGA Cable (not supplied). When connecting the Macintosh computer, the MAC Adapter (not supplied) is required.

SERIAL TERMINAL

Terminal HDB9-PIN

Connect the serial port of computer to this terminal with Serial Cable (not supplied).

Image 43

Eiki LC-VC1 owner manual Configurations Of Terminals, Rgb Terminal, Serial Terminal

Contents

MODEL LC-VC1 MULTIMEDIA PROJECTORTO THE OWNER SAFETY PRECAUTIONSSAFETY INSTRUCTIONS AC Power Cord for the United States and Canada AC POWER CORD REQUIREMENTCOMPLIANCES Federal Communication Commission NoticeSETTING TABLE OF CONTENTSFEATURES AND DESIGN PREPARATION CONNECTING PROJECTORFEATURES AND DESIGN Page PREPARATION CONNECTING AC POWER CORDPOSITIONING THE PROJECTOR LENS SHIFT ADJUSTMENTRECOMMENDATION MOVING PROJECTOR ADJUSTABLE FEETCAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR Page Audio Cable RCA x Speaker Cable Mini x 1 stereo Cables used for connection * = Cables are notsupplied with this projector Video Cable RCA x Video Cable RCA x 3*, BNC x 1 *, BNC x 2* or BNC x S-VIDEO CableAudio Cables RCA x 2 or RCA x 1 - Mini Plug mono MAC Adapter in the case of connecting Macintosh computerVGA Cable HDB 15 pin Video Cable BNC Speaker Cable Mini Plug stereoPage TOP CONTROL OPERATING RANGE Remote Control Unit can be used as either Wired or WirelessREMOTE CONTROL BATTERIES INSTALLATION WIRED REMOTE CONTROLOPERATIONS HOW TO OPERATE ON-SCREEN MENU FLOW OF ON-SCREEN MENU OPERATIONPress MENU BUTTON for PC input source MENU BARTURNING OFF THE PROJECTOR TURNING ON PROJECTORKEYSTONE ADJUSTMENT ZOOM ADJUSTMENTFOCUS ADJUSTMENT LENS SHIFT ADJUSTMENTNO SHOW FUNCTION MUTE SETTINGPICTURE FREEZE FUNCTION DIRECT OPERATION MENU OPERATIONSELECT COMPUTER SYSTEM MANUALLY AUTO PC ADJUSTMENTThe number of total dots in one horizontal period. Press POINT MANUAL PC ADJUSTMENTAdjusts clamp level. When the image has a dark bars, try this whenever you use itAdjustment of horizontal area displayed with this projector. Press NOTE Specifications are subject to change without notice COMPATIBLE COMPUTER SPECIFICATIONSIMAGE LEVEL SELECT MENU IMAGE LEVEL SELECT DIRECTPress POINT LEFT button to lighten green tone and POINT RIGHT IMAGE LEVEL ADJUSTMENTPress POINT LEFT button to decrease contrast, and POINT RIGHT Press POINT LEFT button to lighten red tone and POINT RIGHT buttonCompress function Expand functionPanning function source through MENU OPERATION see below MENU OPERATIONVIDEO JACK, YIC JACKS OR S-VIDEO JACK Y, Pb/Cb, Pr/Cr JACKSVIDEO MODE IMAGE LEVEL SELECT DIRECTIMAGE LEVEL SELECT MENU IMAGE LEVEL ADJUSTMENT 3 aspect ratio at wide video aspect ratio of 16 This function decides whether to display the On-Screen Displays Press both MENU and NORMAL buttons on the Remote Control To change the code of the Remote ControlTo change the code of Projector Follow these steps to clean the projection lens WARNING TEMP INDICATORAIR FILTER CARE AND CLEANING CLEANING THE PROJECTION LENSORDER REPLACEMENT LAMP LAMP REPLACEMENTLAMP REPLACE COUNTER 6.If the problem still exists, check the following chart 3. Verify that all power is switched on4.If projector still does not produce an image, re-start the computer Page The specifications are subject to change without notice RGB TERMINAL CONFIGURATIONS OF TERMINALSSERIAL TERMINAL EIKI CZECH SPOL. S.R.O Audio Visual/Video Products EIKI INTERNATIONAL, INCEIKI CANADA EIKI DEUTSCHLAND GMBH