CONNECTING THE PROJECTOR

CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER

(DIGITAL INPUT CONNECTION)

NOTE: This connection need optionally sold Graphic Accelerator Board.

For this information, contact to your authorized dealer.

Before using with digital connection, install (Plug in) Graphic Accelerator

Board into PCI bus slot of the computer and set up the computer

COMPUTER

following instructions in the Graphic Accelerator Board package.

 

 

MONITOR CABLE

 

(NOT PROVIDED)

GRAPHIC

ACCELERATOR

BOARD

INSTALL (PLUG) INTO PCI BUS SLOT

ANALOG OUTPUT

DIGITAL OUTPUT

DIGITAL FLAT PANEL CABLE (NOT PROVIDED)

SERIAL PORT

PS/2 PORT

COMPUTER

R

AUDIO CABLE

AUDIO OUTPUT

L

(NOT PROVIDED)

INPUT

INPUT

 

 

 

 

 

 

 

 

 

COMPUTER

 

 

 

COMPUTER

 

INPUT 1

 

 

 

AUDIO INPUT 1 R

L

(DIGITAL)

 

 

USB 1

CONTROL PORT 1

AUDIO 1

 

ANALOG

 

DIGITAL

 

IN-1

 

 

 

 

R

L

(MONO)

 

 

 

 

COMPUTER

 

 

 

 

 

 

 

 

 

 

 

MOUSE CABLE FOR

USB 2

CONTROL PORT 2

AUDIO 2

R

G

B

H

V

IN-2

PS/2 PORT

 

 

R

L

(MONO)

 

 

 

 

COMPUTER

 

 

 

 

 

 

 

 

 

(PROVIDED)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R/C JACK

SERIAL PORT

AUDIO OUT

 

ANALOG RGB

 

 

OUT

 

 

R

L

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER

MOUSE CABLE FOR

CONTROL PORT

 

 

 

 

 

 

 

 

 

SERIAL PORT

OUTPUT 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(PROVIDED)

 

 

 

 

 

 

 

 

 

 

 

SERIAL PORT CABLE

 

SERIAL

 

 

 

 

 

 

 

 

 

 

PORT

 

 

 

 

 

 

 

 

 

(NOT PROVIDED)

 

OUTPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPUTER

 

 

 

 

 

AUDIO CABLE

 

 

 

AUDIO OUTPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(NOT PROVIDED)

 

 

 

 

 

 

 

 

 

 

AUDIO

INPUT

 

 

 

SPEAKER

 

 

 

L

 

 

R

OUT

Speaker (L)

 

Speaker (R)

 

 

 

 

 

L

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Amp.

R

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on.

16

Page 16
Image 16
Eiki LC-X3/X3L instruction manual For this information, contact to your authorized dealer