ENGLAND
A
DESCRIPTION (starts at page 85)
1 | Seat | 6 | Throttle lever | 11 | Gear lever (MEC) |
2 | Steering wheel | 7 | Battery | 12 | Agjusting levers for cutting height |
3 | Grass catcher bag | 8 | Blade coupling lever | 13 | Motor safety housing |
4 | Blade | 9 | Brake pedal | 14 | Pilot light for |
5 | Ignition key | 10 | Brake lever | 15 | Advance pedal (HYDRO) |
TECHNICAL DETAILS
B
| Engine |
|
| 8,5 Hp ⎟ 12,5 Hp |
|
|
|
|
|
|
|
|
|
| Electric starter |
|
| Electric |
|
|
|
|
|
|
|
|
|
| Advance |
| Five forward gears and one reverse gear. |
| ||
|
|
|
|
|
|
|
| Maximum speed |
|
| 9,0 Km/h |
|
|
|
|
|
|
|
|
|
| Grass collection bin |
| 2000 mm x 820 mm x 1020 mm |
|
| |
|
|
|
|
|
|
|
| Body |
|
| Polypropylene |
|
|
|
|
|
|
|
|
|
| Cutting plate |
|
| Sheet steel |
|
|
|
|
|
|
|
|
|
| Cutting width |
|
| 67 - 76 cm |
|
|
|
|
|
|
|
|
|
| Cutting height regulation |
|
| Centralised on 5 positions |
|
|
|
|
|
|
|
|
|
| Curvature radius |
|
| 1,5 m |
|
|
|
|
|
|
|
|
|
| Grass collection bag |
|
| 150 litre |
|
|
|
|
|
|
|
|
|
| Tyres | Height |
| Width | Recommended pressure |
|
|
|
|
|
|
|
|
| front | 265 mm |
| 85 mm | 1,5 bar |
|
|
|
|
|
|
|
|
| rear | 360 mm |
| 120 mm | 2 bar |
|
|
|
|
|
|
|
|
| Weight with collection bag |
| 145 |
|
| |
|
|
|
|
|
| |
ASSEMBLY OF THE GRASS COLLECTION SACK (starts at page 85) |
|
| ||||
The grass collection bag is included with all |
| - 1 Fabric bag with clips |
|
| ||
If the bag comes with the product then it not an accessory therefore delete the |
| - 2 |
|
| ||
word accessory and replace with part. |
|
|
|
|
|
For assembly, you need the following parts: | 1. Allow the bag to slide on the frame and secure with suitable clips. | |
- 1 Frame | ||
| ||
- 2 Hexagonal screws (M6x16) |
| |
- 3 |
|
ASSEMBLY
UNPACKING/ ASSEMBLY
The
1.Unpack all the parts that have been delivered. Dispose of the carton and pallet in an environmentally friendly way.
2.Check all the parts
3.Begin assembly.
WHEEL ASSEMBLY (starts at page 85)
C1. Mount the front wheels on the pins (15), positioning a washer (16), the wheel (17) and a washer (18).
2.Secure with a stop (19).
3.Mount the rear wheels on the pins.
STEERING WHEEL ASSEMBLY (starts at page 86)
D1. Fix the steering wheel (2) pushing until it is connected with the steering column (20).
2. Secure the steering wheel (2) by means of the socket pin (21); put the socket pin through the openings (on the steering column and steering wheel)
ENGINE GUARD ASSEMBLY (see page 86)
DInsert the two rear ends into the special slots in the casing and fix the guard by
1 inserting the washers and M5 nuts on M5 x 20 screws and fix to the casing.
SEAT ASSEMBLY (starts at page 86)
D1. Fasten the seat (1) to the support plate (22) through the 4 M8 x 18 screws.
2 Assemble with 4 washers Ø 9 x 24 and 4 grower.
2.Before tightening the screws, adjust the position of the seat on the holes of the plate to suit the user's needs.
It is strictly forbidden to start the
Attention: Assemble the wheel with valve outwards.
The openings at the steering wheel and at the steering column must be in exact alignment.
Check at regular intervals that the nuts are tightly screwed down.
D3
ASSEMBLY OF THE GRASS COLLECTION BAG (starts at page 86)
Fasten the bin to the rear part of the
ADJUSTING THE CUTTING HEIGHT
E
Before the cutting height is adjusted, the engine must be switched off and the blades must have come to complete standstill.
ADJUSTMENT (starts at page 86)
1.Push the adjustment lever (12) outwards in order to release it from its seat.
2.Push the lever into the required notch for the cutting height.
3.Release the lever slowly till it sticks in the notch.
The cutting height is now set.
15