12

 

 

 

The System Setup and Other Setup menus

ZONE Setup

The volume setting and tone for the sub zones that can be used with this receiver can be changed and adjusted here.

CAUTION

!Note that when Volume Level is set to 0 dB Fixed, the audio output from the AUDIO ZONE 2 OUT terminals is set to the maximum. Also, depending on the volume setting on the connected amplifier, large volumes may be produced even when Volume Level is set to –40 dB Fixed.

1Select ‘ZONE Setup’ from the Other Setup menu.

2Select ‘ZONE 2’ or ‘ZONE 3’, then press ENTER.

3Select the Volume Level setting you want.

When making multi-zone connections using the AUDIO ZONE 2 OUT or AUDIO ZONE 3 OUT terminals and performing playback in Zone 2 or Zone3, you can set whether to adjust the Zone 2 or Zone3 volume on the receiver or to fix it to a specific volume (–40 dB Fixed or 0 dB Fixed). This is set to Variable upon shipment from the factory, allowing the volume to be adjusted on the receiver. If you would like to adjust the volume from the connected amplifier, make the setting below.

For ZONE 2, this setting is not possible if multi-zone settings have been made using the speaker terminals and Speaker System is set to ZONE 2. In this case, adjust the volume for the sub zones on the receiver.

!Variable (default) – The Zone 2/Zone3 volume is adjusted from the receiver.

!–40 dB Fixed/0 dB Fixed – The Zone 2/Zone 3 volume level output from the receiver is fixed to the value set here.

4 Select the Power ON Level setting you want.

The sub zone volume is set to the volume selected here when the sub zone is turned on using the multi-zone func- tion. Zones 2 and 3 can be set separately.

When Volume Level is set to –40 dB Fixed or 0 dB Fixed, the volume is fixed to that level, so the volume cannot be set here.

!LAST (default) – When MULTI-ZONE is turned on, the volume is set to the level set the last time you were listening to that zone.

!“---” – When MULTI-ZONE is turned on, the volume for that zone is set to the minimum.

!–80.0dBto 0dB – When MULTI-ZONE is turned on, the volume is set to the level set here. The volume can be set up to the value set at Volume Limit below.

5 Select the Volume Limit setting you want.

The maximum volume for the zone selected in step 2 can be set.

!OFF (default) – The maximum volume is not limited.

!–20.0dB/–10.0dB– The maximum volume is limited to the value set here.

6Select the Mute Level setting you want.

The mute level for the zone selected in step 2 can be set.

This sets how much the volume is to be turned down when MUTE is pressed.

!FULL (default) – No sound.

!–40.0dB/–20.0dB– The volume will be turned down to the level specified here.

7Adjust Lch Level and Rch Level.

The channel level for the zone selected in step 2 can be set.

The level can be adjusted between –12.0dBand +12.0dB, in 1 dB steps.

8Select the HPF (High Pass Filter) setting you want.

This can only be set when ZONE 2 is selected in step 2.

The low frequency component output from the AUDIO ZONE 2 OUT terminals is cut. When a subwoofer is connected in Zone 2, we recommend setting this to “ON”. This is only valid when Zone 2 is connected using the AUDIO ZONE 2 OUT terminals.

!OFF (default) – The High Pass Filter function is disabled.

!ON – The High Pass Filter function is enabled.

9 Select the TONE setting you want.

This can only be set when ZONE 2 is selected in step 2.

The bass and treble for ZONE 2 can be adjusted. When BYPASS is selected, the original sound is played as such. When ON is selected, the BASS and TREBLE can be adjusted.

!When the speaker terminals are being used for Zone 2, the TONE settings cannot be made.

10 Adjust the bass (BASS) and treble (TREBLE) to your tastes.

This can only be set when ZONE 2 is selected in step 2 and ON is selected in step 8.

The BASS and TREBLE can each be adjusted between –10.0dBand +10.0dB, in 1 dB steps.

11When you’re finished, press RETURN.

You will return to the Other Setup menu.

EXTENSION Setup

!Default setting: OFF

A separately sold the CU-RF100 can be used to operate the receiver by RF communications. To do so, set the EXTENSION setting to ON. When ON is set here, the receiver can be operated even when the receiver is in the standby mode.

1Select ‘EXTENSION Setup’ from the Other Setup menu.

2Select the EXTENSION setting you want.

3When you’re finished, press RETURN.

You will return to the Other Setup menu.

Maintenance Mode

Only use this if so instructed by a Pioneer service engineer or custom installer.

90