12

Volume Setup

You can set the maximum volume of this receiver or specify what the volume level will be when the power is turned on.

1Select ‘Volume Setup’ from the Other Setup menu.

2Select the Power ON Level setting you want.

The volume can be set so that it is always set to the same level when the receiver’s power is turned on.

!LAST (default) – When the power is turned on, the volume is set to the same level as when the power was last turned off.

!“---” – When the power is turned on, the volume is set to minimum level.

!–80.0dBto +12.0dB – Specify the volume to be set when the power is turned on, in steps of 0.5 dB.

It is not possible to set a volume level greater than the value specified at Volume Limit setup (see below).

3 Select the Volume Limit setting you want.

Use this function to limit the maximum volume. The volume cannot be increased above the level set here, even by operating VOLUME button (or the dial on the front panel).

!OFF (default) – The maximum volume is not limited.

!–20.0dB/–10.0dB/0.0dB– The maximum volume is limited to the value set here.

4 Select the Mute Level setting you want.

This sets how much the volume is to be turned down when MUTE is pressed.

!FULL (default) – No sound.

!–40.0dB/–20.0dB– The volume will be turned down to the level specified here.

5When you’re finished, press RETURN.

You will return to the Other Setup menu.

Remote Control Mode Setup

!Default setting: 1

This sets this receiver’s remote control mode to prevent erroneous operation when multiple units of the receiver are being used.

1Select ‘Remote Control Mode Setup’ from the Other Setup menu.

2Select the Remote Control Mode setting you want.

3Select ‘OK’ to change the remote control mode.

4Follow the instructions on the screen to change the remote control’s setting.

See Operating multiple receivers on page 71.

5When you’re finished, press RETURN.

You will return to the Other Setup menu.

Software Update

Use this procedure to update the receiver’s software and check the version. There are two ways to update: via the Internet and via a USB memory device.

Updating via the Internet is performed by accessing the file server from the receiver and downloading the file. This procedure is only possible if the receiver is connected to the Internet.

Updating via a USB memory device is performed by downloading the update file from a computer, reading this file onto a USB memory device then inserting this USB memory device into the USB port on the receiver’s front panel. With this procedure, the USB memory device containing the update file must first be inserted into the USB port on the receiver’s front panel.

The System Setup and Other Setup menus

!If an update file is provided on the Pioneer website, download it onto your computer. When downloading an update file from the Pioneer website onto your computer, the file will be in ZIP format. Unzip the ZIP file before saving it on the USB memory device. If there are any old downloaded files or downloaded files for other models on the USB memory device, delete them.

Important

!DO NOT unplug the power cord during updating.

!When updating via the Internet, do not disconnect the LAN cable. When updating via a USB memory device, do not disconnect the USB memory device.

!If updating is interrupted before it is completed, start updating over from the beginning.

!The receiver’s settings may be reset when the software is updated. Information on the models for which the settings are reset is provided on the Pioneer website. Check the website before updating.

1Select ‘Software Update’ from the Other Setup menu.

2Select the update procedure.

!Update via Internet – The receiver checks whether updatable software is available via the Internet.

!Update via USB Memory – The receiver checks whether the USB memory device inserted into the USB port on the receiver’s front panel contains updatable software.

“Accessing” is displayed and the update file is checked. Wait a while.

3Check on the screen whether or not an update file was found.

If “New version found.” is displayed, the update file has been found. The version number and updating time are displayed.

If “This is the latest version. There is no need to update.” is displayed, no update file has been found.

4 To update, select OK.

The updating screen appears and updating is performed.

!The power turns off automatically once updating is completed.

Software Update messages

Status messages

 

Descriptions

 

 

Try disconnecting then reconnecting the USB device or storing the update file again. If the error still

FILE ERROR

 

occurs, try using a different USB memory device.

 

No update file was found on the USB memory device. Store the file in the USB memory device’s root

 

 

 

 

directory.

 

 

 

UPDATE ERROR 1 to

 

Turn the receiver’s power off, then turn it back on and try updating the software again.

UPDATE ERROR 7

 

 

 

 

 

If this message flashes, updating has failed. Update via a USB memory device. Put the update file on a

Update via USB

 

USB memory device and connect the device to the USB port. When the file is found, software updating

 

 

starts automatically.

UE11

 

 

UE22

 

Updating has failed. Use the same procedure to update the software again.

UE33

 

 

89