13

ADAPTER PORT terminal

SymptomRemedy

 

FAQ

Symptom

Remedy

Video signals are not output from the

When a monitor only compatible with resolutions of 480i is connected to the component

component terminal.

terminal and another monitor is connected to the HDMI terminal, the video signals may

 

not be output to the monitor connected to the component terminal. If this happens, do

The Bluetooth wireless technology device cannot be connected or oper- ated. Sound from the Bluetooth wireless technology device is not emitted or the sound is interrupted.

Check that no object that emits electromagnetic waves in the 2.4 GHz band (microwave oven, wireless LAN device or Bluetooth wireless technology apparatus) is near the unit. If such an object is near the unit, set the unit far from it. Or, stop using the object emitting the electromagnetic waves.

Check that the Bluetooth wireless technology device is not too far from the unit and that obstructions are not set between the Bluetooth wireless technology device and the unit. Set the Bluetooth wireless technology device and the unit so that the distance between them is less than about 10 m (33 ft.) and no obstructions exist between them.

Check that the Bluetooth ADAPTER and the ADAPTER PORT of the unit are correctly connected.

The Bluetooth wireless technology device may not be set to the communication mode supporting the Bluetooth wireless technology. Check the setting of the Bluetooth wireless technology device.

Check that pairing is correct. The pairing setting was deleted from this unit or the Blue- tooth wireless technology device. Reset the pairing.

Check that the profile is correct. Use a Bluetooth wireless technology device that supports A2DP profile and AVRCP profile.

 

the following:

 

— Turn off the power of the monitor connected to the HDMI terminal.

 

— Change the VIDEO PARAMETER menu RES setting (see Setting the Video options on

 

page 65).

 

— Video signals from the HDMI terminal cannot be output to the component terminals.

 

Input the video signals from the player or other source to the composite or component

 

terminals. When using the component terminal, assign it at Input Setup (see The Input

 

Setup menu on page 39).

The picture's movement is unnatural.

When Resolution under VIDEO PARAMETER is set to 1080/24p, the picture may not be

 

displayed properly for some source materials. In this case, set the resolution to some-

 

thing other than 1080/24p (page 65).

 

 

 

 

Settings

 

Symptom

Remedy

The Auto MCACC Setup continually

The ambient noise level may be too high. Keep the noise level in the room as low as

shows an error.

possible (see also Problems when using the Auto MCACC Setup on page 38). If the noise

 

level cannot be kept low enough, you will have to set up the surround sound manually

Video

Symptom

Remedy

No image is output when an input is

Check the video connections of the source component.

selected.

 

For HDMI, or when V.CONV is set to OFF and a TV and another component are con-

 

 

nected with different cords (in Setting the Video options on page 65), you must connect

 

your TV to this receiver using the same type of video cable as you used to connect your

 

video component. For the component video input, however, signals are only output from

 

the HDMI output, so when using the component video input, set V.CONV to ON.

 

Make sure the input assignment is correct for components connected using component

 

video or HDMI cables (see The Input Setup menu on page 39).

 

 

 

Check the video output settings of the source component.

 

 

 

Check that the video input you selected on your TV is correct.

 

 

 

Some components (such as video game units) have resolutions that may not be con-

 

verted. If adjusting this receiver’s Resolution setting (in Setting the Video options on page

 

65) and/or the resolution settings on your component or display doesn’t work, try switch-

 

ing V.CONV (in Setting the Video options on page 65) to OFF.

Can’t record video.

Check that the source is not copy-protected.

 

The video converter is not available when making recordings. Check that the same type

 

of video cable is used for connecting both the recorder and the video source (the one you

 

want to record) to this receiver.

Noisy, intermittent, or distorted

Sometimes a video deck may output a noisy video signal (during scanning, for example),

picture.

or the video quality may just be poor (with some video game units, for example). The

 

picture quality may also depend on the settings, etc. of your display device. Switch off

 

the video converter and reconnect the source and display device using the same type of

 

connection (component or composite), then start playback again.

 

(page 85).

 

 

 

When using only one surround back speaker, connect it to the SURROUND BACK L

 

(Single) terminals.

 

To use a 5.1-channel speaker set, use the surround speakers for the surround channel,

 

not the surround back channel.

 

 

 

Make sure there are no obstacles between the speakers and the microphone.

 

 

 

If Reverse Phase is displayed, try the following:

 

— The speaker’s wiring (+ and –) may be inverted. Check the speaker connections.

 

— Depending on the type of speakers and their installation conditions, Reverse Phase

 

may be displayed even if the speakers are properly connected. If this happens, select

 

GO NEXT and continue.

 

— If the speaker is not pointed to the microphone (listening position) or when using

 

speakers that affect the phase (dipole speakers, reflective speakers, etc.), it may not be

 

possible to properly identify the polarity.

 

 

After using the Auto MCACC Setup,

There may have been some low frequency noise in the room from an air-conditioner,

the speaker size setting is incorrect.

motor, etc. Switch off all other appliances in the room and use Auto MCACC Setup again.

 

Depending on a number of factors (bass reproduction capabilities of the speakers, room

 

size, speaker placement, etc.) this may occur in some cases. Change the speaker setting

 

manually in Speaker Setting on page 85, and use the ALL (Keep SP System) option for

 

the Auto MCACC menu in Automatic MCACC (Expert) on page 77 if this is a recurring

 

problem.

Can’t adjust the Fine Speaker Dis-

Check that the speakers are all in phase (make sure the positive (+) and negative (–)

tance setting properly.

terminals are matched up properly).

 

 

The display shows KEY LOCK ON

With the receiver in standby, press uSTANDBY/ON for about 5 seconds while holding

when you try to make settings.

down SPEAKERS to disable the key lock.

Most recent settings have been

The power cord was disconnected from the wall while adjusting this setting.

erased.

 

Settings are only stored if all the zones are turned off. Turn off all the zones before unplug-

 

 

ging the power cord.

94