EMC FC4500 - page 28

1-16 EMC Fibre Channel Disk-Array Processor Enclosure (DPE) Hardware Reference

About the Rackmount Disk-Array Processor Enclosure

Figure 1-13 SP Fan Pack

Latches on the SP fan pack hold the pack in place.

The SP fan pack has one status light visible when the SP fan pack

cover is removed. The status light is described in the “Monitoring

DPE Status” section of Chapter 3.

You can remove the SP fan pack while the DPE is powered up. If the pack is

removed for more than approximately two minutes, the SPs and disk

modules power down. The SPs and disk modules power up when you

reinstall the SP fan pack.

Latches

Check light

(amber)

Contents

Main Copyright EMC Corporation 2000, 2001. All rights reserved. Trademark Information EMC Fibre Channel Disk-Array Processor Enclos ure (DPE) Hardware Reference Regulatory Notices Manufacturers Declaration of Conformity - CE mark Page Contents Preface Chapter 1 About the Rackmount Disk-Array Processor Enclosure Chapter 2 Installing a Rackmount DPE Chapter 3 Servicing and Upgrading a DPE Appendix A Technical Specifications and Operating Limits Glossary Index Figures Page Page Page Preface Page Page Introduction Page DPE Components Enclosure Page Page Page Midplane Storage Processors (SPs) Page Link Control Cards (LCCs) ! Disk Modules Disk Drives Drive Carrier Power Supplies Standby Power Supply (SPS) Drive Fan Pack SP Fan Pack Page Redundancy in Configurations Page Requirements Site Requirements Installing a Rackmount DPE Cabling Requirements Addressing Requirements Installing a DPE in a Cabinet Installing DPEs on the Mounting Rails in the Cabinet 4. Open the DPE front door as shown below. Page 7. Close the DPE front door, as shown in Figure 2-4. Figure 2-4 Closing and Locking the Front Door B. A. Page Page Page Page A. B. Page C. B. A. D. DPE Powerup and Initialization DPE Powerdown Page Page Monitoring DPE Status Servicing and Upgrading a DPE Page Page Handling CRUs Power Issues and CRUs Page Avoiding Electrostatic Discharge (ESD) Damage Precautions When Removing, Installing, or Storing CRUs Precautions When Handling Optical Cables Replacing or Adding a Disk Module angle to the enclosure, and snapping it into the hinge openings. A. B. C. Page Replacing or Adding a Disk Module 3. Close and lock the front door as shown below. Figure 3-6 Closing and Locking the Front Door B. A. Replacing the SP Fan Pack A. B. Page Replacing an Optical GBIC B A 2. Remove the optical GBIC connector(s) from the SP as shown below. Installing an Optical GBIC Connector AB AB Removing an SP or an SP Filler Module Page Page Installing or Replacing an SP Memory Module Page 3. If you want to install the SP, continue to the next section. Installing an SP or SP Filler Module Alignment notch Installing an SP or SP Filler Module F E 7 2. At the back of the deskside DPE, gently insert the SP or filler module as shown below. B. Replacing or Adding an LCC Module Removing an LCC B. A. B. A. Installing an LCC B. A. A. B. C. D. Replacing the Drive Fan Pack Removing the Drive Fan Pack Installing the Drive Fan Pack A. B. Replacing or Adding a Power-Supply Module Removing a Power-Supply Filler Module A. B. Page 3. Remove the power-supply module, as shown in Figures 3-29 and 3-30. A. B. Installing a Power-Supply Module Page Page Page A Technical Specifications AC Power Requirements Technical Specifications and Operating Limits Size and Weight Page Safety Standards EMI Standards Fibre Channel Related Standards Operating Limits Shipping and Storage Requirements Page E F H J L M N P R S Page Page Index B C D E F G H I M O P R S T V W