EMC FC4500 Replacing or Adding a Power-Supply Module

3-36 EMC Fibre Channel Disk-Array Processor Enclosure (DPE) Hardware Reference

Servicing and Upgrading a DPE

Figure 3-25 Installing the Drive Fan Pack

As soon as the pa ck is in place, the fan s start s pinnin g; the D PE Chec k

light turns off if no other CRUs are faulty; and the Cooling Check

light on each power supply turns off.

Replacing or Adding a Power-Supply Module

CAUTION

To access a power-supply module, you must remove the drive fan

pack. If the drive fan pack is removed for more than two minutes,

the SPs and disk modules power down. The SPs and disk modules

will power up when you reinstall the drive fan pack.

Handle a power supply gently and use an ESD wristband. Do not

remove a power supply until you have a replacement supply or

filler module available.

A. Grasp the latches on the drive fan pack.

B. Squeeze the latches together and

gently push the pack into the

enclosure until it clicks into place.

Check light

Contents

Main Copyright EMC Corporation 2000, 2001. All rights reserved. Trademark Information EMC Fibre Channel Disk-Array Processor Enclos ure (DPE) Hardware Reference Regulatory Notices Manufacturers Declaration of Conformity - CE mark Page Contents Preface Chapter 1 About the Rackmount Disk-Array Processor Enclosure Chapter 2 Installing a Rackmount DPE Chapter 3 Servicing and Upgrading a DPE Appendix A Technical Specifications and Operating Limits Glossary Index Figures Page Page Page Preface Page Page Introduction Page DPE Components Enclosure Page Page Page Midplane Storage Processors (SPs) Page Link Control Cards (LCCs) ! Disk Modules Disk Drives Drive Carrier Power Supplies Standby Power Supply (SPS) Drive Fan Pack SP Fan Pack Page Redundancy in Configurations Page Requirements Site Requirements Installing a Rackmount DPE Cabling Requirements Addressing Requirements Installing a DPE in a Cabinet Installing DPEs on the Mounting Rails in the Cabinet 4. Open the DPE front door as shown below. Page 7. Close the DPE front door, as shown in Figure 2-4. Figure 2-4 Closing and Locking the Front Door B. A. Page Page Page Page A. B. Page C. B. A. D. DPE Powerup and Initialization DPE Powerdown Page Page Monitoring DPE Status Servicing and Upgrading a DPE Page Page Handling CRUs Power Issues and CRUs Page Avoiding Electrostatic Discharge (ESD) Damage Precautions When Removing, Installing, or Storing CRUs Precautions When Handling Optical Cables Replacing or Adding a Disk Module angle to the enclosure, and snapping it into the hinge openings. A. B. C. Page Replacing or Adding a Disk Module 3. Close and lock the front door as shown below. Figure 3-6 Closing and Locking the Front Door B. A. Replacing the SP Fan Pack A. B. Page Replacing an Optical GBIC B A 2. Remove the optical GBIC connector(s) from the SP as shown below. Installing an Optical GBIC Connector AB AB Removing an SP or an SP Filler Module Page Page Installing or Replacing an SP Memory Module Page 3. If you want to install the SP, continue to the next section. Installing an SP or SP Filler Module Alignment notch Installing an SP or SP Filler Module F E 7 2. At the back of the deskside DPE, gently insert the SP or filler module as shown below. B. Replacing or Adding an LCC Module Removing an LCC B. A. B. A. Installing an LCC B. A. A. B. C. D. Replacing the Drive Fan Pack Removing the Drive Fan Pack Installing the Drive Fan Pack A. B. Replacing or Adding a Power-Supply Module Removing a Power-Supply Filler Module A. B. Page 3. Remove the power-supply module, as shown in Figures 3-29 and 3-30. A. B. Installing a Power-Supply Module Page Page Page A Technical Specifications AC Power Requirements Technical Specifications and Operating Limits Size and Weight Page Safety Standards EMI Standards Fibre Channel Related Standards Operating Limits Shipping and Storage Requirements Page E F H J L M N P R S Page Page Index B C D E F G H I M O P R S T V W