Section 19 • Configuration

logging and troubleshooting. Setting these parameter will set the hardware clock embedded in the Vission 20/20 CPU. If the time is not retained after powering down the panel, the operator should check and/or re- place the coin style battery on the panel SBC behind the touchscreen.

Format:

•Selection to choose between 12 hour or 24 hours clock.

Hour:

•Entry box to set the clock hours. AM or PM drop-down box will available if the 12 hour format is selected.

Minute:

•Entry Box to set the clock minutes. Second:

•Entry Box to set the clock seconds. Year:

•Entry Box to set the current year. Month:

•Entry Box to set the current month. Day:

•Entry Box to set the current date.

Communications

The communication section is the control center for all communications to the Vission 20/20 panel. It is possi- ble to have multiple modes of communications enabled and used. However, only one mode can be used to con- trol the Vission 20/20 which is selected in the “Active Remote Control” drop-down box. For a complete list of communication registers, please refer to the Vission 20/20 communication table.

Active Remote Control:

•Selects the mode of remote control. The operator can select between Direct I/O, Serial, or Ethernet.

Direct I/O:

•Enables the Direct I/O inputs. Once selected a pop-up will be displayed and the operator will need to choose a one of the three Direct I/O options

Serial (Modbus RTU):

•Enables the Serial Modbus RTU protocol. Once se- lected, the remainder of the serial setpoints will be available for editing.

Panel ID:

•Panel Identifier used by the controller when commu- nicating with multiple panels.

Port:

•The Vission 20/20 has two ways to communicate on serial bus. Either via the built in serial port, P12, or through one of the USB ports. This drop-down box allows the operator to chose which one will be used.

Baud Rate:

•Sets the Baud Rate for the serial communication. Data Bits:

•Fixed at 8 Data bits.

Stop Bits:

•Identifies the end of character for re-synchronizing. Parity:

•Identifies the type of error detection.

Ethernet:

•Enables the Ethernet port. Once selected, the re- mainder of the Ethernet setpoints will be available for editing.

Panel ID:

•Panel Identifier used by the controller when commu- nicating with multiple panels.

IP Address:

•Entry box to set the IP address. Subnet Mask:

•Entry box to set the Subnet Mask. Gateway:

•Entry box to set the Gateway address. Protocol:

•Drop-down box to select the type of protocol used to remotely control the Vission 20/20.

Touchscreen

The “Calibrate” button changes the screen into touch- screen calibration mode. Calibrating the touchscreen is only required if the operator finds that the pointer ar- row no longer follows his finger. The calibration mode requires the operator to touch the four corners of the touchscreen and then the accept button.

Anti-Recycle

Anti-Recycle defines the method of motor protection

19 – 2

Vission 20/20 • Operation and Service Manual •Vilter/Emerson • 35391SC 1.8.5153

Page 91 Page 93
Page 92
Image 92
Emerson 20/20 service manual Communications, Touchscreen, Anti-Recycle
Page 91 Page 93

20/20 specifications

Emerson 20/20 is an advanced platform designed for real-time data analytics, visualization, and operational optimization in industrial settings. This robust solution aims to empower organizations by providing actionable insights derived from their operational data, enabling enhanced decision-making and improved efficiency.

One of the standout features of Emerson 20/20 is its ability to integrate seamlessly with various sources of data, whether structured or unstructured. It consolidates information from different systems, such as historians, control systems, and ERP software, allowing users to gain a comprehensive view of their operations. This integration capability is crucial for businesses looking to maximize their data utilization without being confined to a single data source.

The platform employs powerful analytics tools that utilize machine learning and artificial intelligence technologies. These tools are designed to automatically identify patterns, anomalies, and trends in real-time. By leveraging predictive analytics, Emerson 20/20 helps organizations forecast potential issues before they escalate, allowing for proactive maintenance and minimizing downtime.

Emerson 20/20 also features user-friendly visualization dashboards, which provide customizable views tailored to individual user roles. This means that whether you are a plant manager, a process engineer, or an executive, you can access relevant data that speaks directly to your needs. These dashboards facilitate easier understanding of complex data sets, promoting informed decision-making across the organization.

One notable characteristic of Emerson 20/20 is its adaptability and scalability. Businesses of all sizes can implement the platform and scale its features according to their needs. This flexibility ensures that both small operations and large enterprises can derive value from the solution, making it an attractive option for various industries.

Additionally, the platform is designed with cybersecurity in mind, ensuring that data integrity and confidentiality are maintained. This aspect is increasingly important as industries become more interconnected and target more sophisticated cyber threats.

In summary, Emerson 20/20 stands out as a powerful tool for organizations seeking to harness their operational data effectively. With its advanced analytics capabilities, seamless integration, customizable visualization, and scalable design, it offers a comprehensive solution to optimize industrial performance and support data-driven decision-making. As businesses continue to navigate the complexities of modern operations, Emerson 20/20 provides the insights necessary to stay competitive and responsive to changing market demands.
Top Page Image Contents