Emerson TCL - page 45

37

MODEL TCL SECTION 7

PROGRAMMING THE ANALYZER

7.5.3 Procedure – Configuring the Measurement

1. Press MENU. The main menu screen appears. Move the cursor to

Program and press ENTER.

2. Choose Measurement.

3. The screen at left appears only if you have a dual input 1056. Choose the

Chlorine sensor.

4. The screen summarizes the present configuration for the chlorine sensor.

There are four items: Measure, Units, Filter, and Resolution

To make a change, move the cursor to the desired line and press ENTER.

A screen will appear in which the present setting can be edited. To store

the setting press ENTER.

a. For Measurement choose Total Chlorine.

b. Leave Filter at the default value unless readings are noisy.

For an explanation of terms, see sections 7.5.2.

6. To return to the main display, press MENU then EXIT.

Program

Outputs

Alarms

Measurement

Temperature

Measurement

Configure?

Sensor1

Sensor 2

Sensor 1

S1 Configure

Measure Total Cl

Units: ppm

Filter: 5 sec

Resolution: 0.001 ppm

Measure:

Contents

Main Model TCL Total Chlorine Analyzer Instruction Manual ESSENTIAL INSTRUCTIONS Page CAUTION DANGER About This Document MODEL TCL TOTAL CHLORINE ANALYZER TABLE OF CONTENTS TABLE OF CONTENTS CONT'D. LIST OF TABLES LIST OF FIGURES Page SECTION 1. DESCRIPTION AND SPECIFICATIONS Model 1056 Chlorine Analyzer Model 499A CL-02 Sensor Model TCL Sample Conditioning System 1.1 FEATURES Page 1.3 SPECIFICATIONS MODEL 1056 ANALYZER 1.2 SPECIFICATIONS SAMPLE CONDITIONING SYSTEM GENERAL SAMPLE REQUIREMENTS SAMPLE CONDITIONING SYSTEM 1.4 SPECIFICATIONS MODEL 499ACL-02 SENSOR 1.5 PERFORMANCE SPECIFICATIONS COMPLETE SYSTEM 1.6 ORDERING INFORMATION AND ACCESSORIES MODEL TCL REAGENT-BASED CHLORINE SYSTEM ACCESSORIES SAMPLE CONDITIONING SYSTEM ACCESSORIES Sensor ACCESSORIES 1055-24 Analyzer ACCESSORIES 54eA Analyzer FOR FIRST TIME VARIOPOL INSTALLATIONS SECTION 2. PRINCIPLES OF OPERATION SECTION 3. INSTALLATION 3.1 UNPACKING AND INSPECTION 3.2 INSTALLATION. CAUTION MODEL TCL SECTION 3 INSTALLATION ( Page Page Page SECTION 4. WIRING 4.1 PREPARE ANALYZER CONDUIT OPENINGS 4.2 PROVIDE POWER TO THE SAMPLE CONDITIONING SYSTEM 4.3 MAKE POWER, ALARM, OUTPUT, AND SENSOR CONNECTIONS IN THE ANALYZER CAUTION 4.4 SENSOR WIRING WARNING Page Page MENU TREE SECTION 5. START-UP 5.1 PREPARE THE REAGENT 5.2 ZERO THE SENSOR 5.3 START SAMPLE FLOW 5.4 BEGIN OPERATION AND CALIBRATE THE SENSOR SECTION 6. DISPLAY AND OPERATION 6.1. DISPLAY 6.2 KEYPAD Page Page Page Page SECTION 7. PROGRAMMING THE ANALYZER 7.1 GENERAL 7.2 DEFAULT SETTINGS TABLE 7-1. DEFAULT SETTINGS ITEM CHOICES DEFAULT Page 7.3 CONFIGURING, RANGING, AND SIMULATING OUTPUTS. Page Page Page Page Page Page Page Page Page Page Page Page SECTION 9. CALIBRATION 9.1 INTRODUCTION 9.2 CALIBRATING TEMPERATURE Page 9.3 CALIBRATING TOTAL CHLORINE Page Page Page Page SECTION 10. MAINTENANCE 10.1 ANALYZER 10.2 TOTAL CHLORINE SENSOR CAUTION Page 10.3 SAMPLE CONDITIONING SYSTEM Page Page Page Page WARNING Page SECTION 11. TROUBLESHOOTING 11.3 TROUBLESHOOTING WHEN A FAULT MESSAGE IS SHOWING Page 11.4 TROUBLESHOOTING WHEN A WARNING MESSAGE IS SHOWING 11.5 TROUBLESHOOTING WHEN NO ERROR MESSAGE IS SHOWING Page Page Page 11.6 SIMULATING TEMPERATURE SECTION 12. RETURN OF MATERIAL 12.1 GENERAL. 12.2 WARRANTY REPAIR. 12.3 NON-WARRANTY REPAIR.