Command Shaft Rotation
TABLE 1. VSS / VSR / VSM COMMAND SHAFT ROTATION AND TRAVEL
COMP.
MODEL VSR 111 VSR 151 VSR 221 VSR 301 VSS 451 VSS 601 VSS 751 VSS 901 VSS 1051 VSS 1201 VSS 1501 VSS 1801 VSM 71 VSM 91 VSM 101 VSM 151 VSM 181 VSM 201 VSM 301 VSM 361 VSM 401 VSM 501 VSM 601 VSM 701
COMMAND SHAFT ROTATION
CAPACITY | VOLUME | ||
INC | DEC | INC | DEC |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CW | CCW | CW | CCW |
CW | CCW | CW | CCW |
CW | CCW | CW | CCW |
CW | CCW | CW | CCW |
CW | CCW | CC | CCW |
CW | CCW | CW | CCW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CCW | CW | CCW | CW |
CW | CCW | CW | CCW |
CW | CCW | CW | CCW |
CW | CCW | CW | CCW |
|
|
|
|
NO. OF TURNS / ROTATION ANGLE / SLIDE TRAVEL
| CAPACITY |
| VOLUME | ||||
TURNS/ANGLE/TRAVEL | TURNS/ANGLE/TRAVEL | ||||||
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
1.09 | / | 392 | / 4.283” | 0.63 | / | 227 | / 2.473” |
1.09 | / | 392 | / 4.283” | 0.63 | / | 227 | / 2.473” |
1.22 | / | 439 | / 4.777” | 0.74 | / | 266 | / 2.889” |
1.22 | / | 439 | / 4.777” | 0.74 | / | 266 | / 2.889” |
1.36 | / | 490 | / 5.325” | 0.82 | / | 295 | / 3.200” |
1.36 | / | 490 | / 5.325” | 0.82 | / | 295 | / 3.200” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.80 | / | 288 | / 3.141” | 0.45 | / | 162 | / 1.767” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
0.91 | / | 328 | / 3.568” | 0.52 | / | 187 | / 2.045” |
NOTES: The manual operating shaft on the gear motor should be turned the opposite direction of the desired command shaft rotation. The capacity and volume control motors are equipped with a brake, if it is necessary to operate the control motors manually, the brake must be disengaged. The brake can be disengaged by pushing on the motor shaft on the cone end. The shaft should be centered in its travel. Do not use excessive force manually operating the motor or damage may result.
48
