THERMOCOUPLE (NATURAL)
GAS CONTROL KNOB
SHOWN IN "OFF" POSITION.

MILLIVOLT VALVE lighting instructions

FOR YOUR SAFETY READ BEFORE LIGHTING

Warning: If you do not follow these instructions exactly, a fire or explosion may result caus-

ing property damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.Before lighting smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

What To Do If You Smell Gas

•Do not try to light any appliance.

•Do not touch any electrical switch;

Do not use any phone in your building.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it; call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information label.

2.Open bottom louver assembly.

3.Set REMOTE/OFF/ON switch to

"OFF."

4. Turn off all electric power to the appliance (if applicable).

5.Push in gas control knob slightly

and turn clockwise to "OFF." NOTE: Knob cannot be

turned from "PILOT" to "OFF" unless knob is pushed in slightly. Do not force.

6.Wait ten (10) minutes to clear out any gas. Then smell for gas, including

near the floor. If you smell gas,

STOP! Follow "B" in the safety information above. If you do not smell gas, go to the next step.

7.Find pilot - Follow metal tube THERMOCOUPLE(LPG)

from gas control. The pilot is

behind the burner on the right side.

REMOTE

OFF

ON

PILOT THERMOPILE

ELECTRODE

8. Turn gas control knob counterclockwise

to

"PILOT."

 

9.Push in control knob all the way and hold in. Repeatedly push the Piezo Ignitor Button until the pilot is lit. Continue to hold the control knob in for about one (1) minute after the pilot is lit. Release knob, and it will pop back up. Pilot should remain lit. If it goes out, repeat steps 5 through 9.

•If knob does not pop up when released, STOP and IM- MEDIATELY call a qualified service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to "OFF" and call your service technician or gas supplier.

10. Turn gas control knob counterclockwise

to "ON."

11.Set REMOTE/OFF/ON switch to desired setting.

12.Turn on all electric power to the appliance (if applicable).

13.Close bottom louver assembly.

TO TURN OFF GAS TO APPLIANCE

1.Open bottom louver assembly.

2.Set REMOTE/OFF/ON switch to "OFF."

3.Turn off all electric power to the appliance if service is to be performed (if applicable).

4.Push in gas control knob slightly and turn clockwise to "OFF." Do not force.

5.Close bottom louver assembly.

Page 20

26670-0-0110

Page 19 Page 21
Page 20
Image 20
Empire Comfort Systems VFP36SP32EN-2, VFP36PP32EN-2, VFP36SP32EP-2, VFP36PP32EP-2 Millivolt Valve lighting instructions
Page 19 Page 21

VFP36PP32EP-2, VFP36SP32EP-2, VFP36SP32EN-2, VFP36PP32EN-2 specifications

Empire Comfort Systems offers a range of high-quality vent-free fireplaces, including the models VFP36SP32EN-2, VFP36SP32EP-2, VFP36PP32EP-2, and VFP36PP32EN-2. These models are engineered to provide both warmth and elegance, making them an exceptional choice for enhancing the ambiance of any living space.

One of the key features of these vent-free fireplaces is their impressive heating efficiency. They are designed to provide an optimal heat output without the need for a traditional flue or venting system, allowing homeowners to enjoy a cozy atmosphere without the associated installation and maintenance costs. With their high-efficiency gas burning systems, these fireplaces convert a significant portion of their fuel into heat, resulting in less energy waste and lower utility bills.

The VFP models are equipped with state-of-the-art flame technology, which produces realistic and visually appealing flames that mimic the beauty of a traditional wood-burning fire. The flame appearance can enhance any room’s aesthetics, creating a warm and inviting atmosphere that is perfect for gatherings or quiet evenings at home.

Another notable characteristic is the variety of styles available. The VFP36PP models feature a more modern, contemporary design, while the VFP36SP models have a traditional aesthetic that fits well with classic décor. This versatility in style allows homeowners to select a model that best suits their interior design preferences.

Safety is also a top priority with these fireplaces. They come with built-in safety features, including an automatic shut-off system that activates if the pilot light goes out, ensuring peace of mind for users. The models are also equipped with thermostat controls, allowing for easy temperature adjustments to maintain a comfortable environment.

In terms of fuel options, these vent-free fireplaces can operate on both natural gas and propane, providing flexibility based on the needs and availability of fuel sources. Moreover, they have a compact design, making them an excellent choice for smaller spaces or homes where traditional fireplaces may not be feasible.

In summary, Empire Comfort Systems' VFP36SP32EN-2, VFP36SP32EP-2, VFP36PP32EP-2, and VFP36PP32EN-2 models stand out for their efficiency, aesthetic appeal, safety features, and versatility. These vent-free fireplaces are an exceptional addition to any home, offering warmth and style with the convenience of easy installation and operation.
Top Page Image Contents