TROUBLESHOOTING
1. | Spark electrode does not produce spark. | b. INTERLOCK latching device is operative - see "Lighting |
| a. Spark electrode broken - replace. | Instructions," Page 12, Step 9. |
| b. Ignitor wire may not be attached to spark electrode - | c. Thermocouple not tightened into gas control - tighten |
| attach. | thermocouple. |
| c. Ignitor wire damaged - replace. | d. Pilot flame not surrounding thermocouple - clean pilot, |
| d. Piezo ignitor defective - replace. | see Page 14. |
2. Spark electrode produces spark but pilot does not light. | e. Inlet gas pressure too low, contact gas supplier. | |
| a. No gas to heater - turn on gas. | f. Thermocouple defective - replace. |
| b. PILOT position not properly aligned - turn gas control | g. Gas control defective - replace. |
| knob to PILOT position and depress. | 4. Main burner does not ignite. |
| c. Pilot is blocked from spider web or dirt - clean pilot, see | a. Main burner orifice is blocked - clean, see "Main Burner |
| Page 14. | Flame Characteristics," Page 13. Attention: The number |
3. | Pilot flame does not stay "ON" when control knob is | stamped on the main burner orifice is a millimeter |
| released. | diameter. |
| a. Control knob in PILOT position not completely | b. Inlet gas pressure too low, contact gas supplier. |
| depressed or held in long enough. | 5. Heater keeps shutting "OFF" during normal operation. |
|
| a. Pilot is blocked - clean pilot, see Page 14. |
|
| b. Inlet gas pressure too low, contact gas supplier |
HOW TO ORDER REPAIR PARTS
Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer.
All parts listed in the Parts List have a Part Number. When ordering parts, first obtain the Model Number from the name plate on your equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate illustration and list. Be sure to give all this information . . .
Unvented Heater Model Number |
|
|
| Part Description |
| |
Unvented Heater Serial Number |
|
|
| Part Number |
|
|
Type of Gas (Propane or Natural) |
|
|
|
|
|
Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store.
Shipments contingent upon strikes, fires and all causes beyond our control.
PARTS LIST
SR-10T
PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.
INDEX | PART |
| INDEX | PART |
|
NUMBER | NUMBER | DESCRIPTION | NUMBER | NUMBER | DESCRIPTION |
|
|
|
|
|
|
1 | 13347 | CASING SIDE ASSEMBLY - LEFT |
|
| (INCLUDES ITEMS 16 & 17) |
2 | CASING BACK | 15 | PILOT ASSEMBLY (NAT ONLY)) | ||
3 | PIEZO IGNITOR |
|
| (INCLUDES ITEMS 16 & 17) | |
4 | CASING SIDE ASSEMBLY - RIGHT | 16 | PILOT THERMOCOUPLE | ||
5 | VALVE BRACKET | 17 | SPARK IGNITOR | ||
6 | GAS VALVE | 18 | PILOT BRACKET (NAT) | ||
7 | 12438 | TUBING - GAS VALVE TO BURNER | 18 | PILOT BRACKET (LPG) | |
8 | 12437 | TUBING - INLET REGULATOR TO GAS | 19 | ORIFICE SHIELD | |
|
| VALVE | 20 | CHROME GRILL | |
9 | 10753 | iNLET REGULATOR BRACKET | 21 | CASING LOUVER (2 REQUIRED) | |
10 | INLET REGULATOR - NAT | 22 | REFLECTOR ASSEMBLY | ||
10 | INLET REGULATOR - LPG | 23 | HEAT SHIELD | ||
11 | TUBING - GAS VALVE TO PILOT | 24 | BULB CLIP | ||
12 | ORIFICE HOLDER | 25 | OPTIONAL | ||
13 | MAIN BURNER ORIFICE - NAT |
|
| KIT | |
13 | MAIN BURNER ORIFICE - LPG | NS | IGNITOR WIRE | ||
14 | BURNER | NS | HARDWARE PACKAGE | ||
15 | PILOT ASSEMBLY (LPG ONLY)) |
|
|
| |
|
|
|
|
|
|
Page 16 | Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois |