![](/images/new-backgrounds/1026482/2648277x1.webp)
Installation
INSTALLATION OF THE SURROUND PANEL - INSERT:
The trim set for your surround panel must be installed before installing the surround panel onto the unit, if not already done.
1. Remove the backing off the magnets and stick them inside the trim pieces as shown in Figure 51.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 2. Attach one side trim to the top trim, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| using a corner bracket (see Figure |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 52) to secure pieces together. There |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| are two (2) main pieces to each |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| corner bracket (see Figure 53). When |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| installing the corner pieces into the |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| trim, the “B FACE” sides must face |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| each other and the screw heads are to |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| face out. With the bracket in place and |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| the top and a side trim snug together, |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| use a flat head screwdriver to turn |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Magnetic Strips |
|
|
|
| the two (2) screws in the bracket to | ||||||
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| tighten it into the trim. |
|
|
|
|
|
|
| |||||||||||
|
|
| Figure 51: Magnet placement on trim. |
| 3. Slide the two (2) attached trim pieces | ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| onto the surround panel. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
4. Attach the other side trim piece to the top trim, using the same method used in Step 1.
| 5. Place the second side of the trim |
| on the surround panel in the same |
| manner used on the first side and |
| secure in the same manner. |
Figure 52: Corner brackets for trim. | |
| Figure 53: Two pieces of |
| corner bracket. |
| 6. On the side trims, there are holes 2” |
| (50 mm) from either end. Use a Phillips |
| screwdriver to place a #8 screw 11⁄4” |
| long in each hole and tighten (refer to |
| Figure 54). This will keep the trim tight |
| against the surround. |
| There are two (2) hooks on either side |
| of the inside of the panel. Line up the |
| openings on the hooks with the screws |
| on the outside of either shroud (see |
Figure 54: Screw to hold | Figure 55). Push the surround in and |
the trim against the | push it down into place. |
surround. | Figure 55: Installation of Panel. |
| |
| 39 |