Manuals / Enviro / Household Appliance / Stove

Enviro 2100 Freestanding owner manual Outside AIR

Models: 2100 Freestanding

1 22
Download 22 pages 30.96 Kb
Page 13
Image 13

Installation

OUTSIDE AIR:

A 4” (10.2 cm) fresh air adapter kit is available. This adapter can be installed either on the back pedestal or through the floor under the pedestal.

Place the 1⁄4” mesh screen between the fresh air adapter and the body of the pedestal (as shown to right).

NOTE: Fresh air connection to the unit must be a non combustible pipe, example: 4” (10.2 cm) single wall aluminum flex pipe.

NOTE: Remove the 4” (10.2 Cm) knock out on the rear of the pedestal if room air is to be used for combustion air

INSTALLATION OF A LISTED, FACTORY BUILT CHIMNEY:

���� �� ��������

1.Set floor protector and stove in location in accordance with the “Clearances To Combustibles - Freestanding”

2.Mark the position for the ceiling hole by using a plumb bob.

3.Move this location, if necessary, to avoid floor joists, ceiling rafters while still maintaining required clearances.

4.Mark the hole for the outside air kit.

5.Move the stove out of the way.

6.Cut a pilot hole in the ceiling.

7.Cut a hole for the ceiling penetration components and frame in the sides of the hole in both the ceiling and roof. Check, and follow chimney manufacturer’s instructions for all of these steps.

8.Install the support box and chimney through the roof. Install the slip section for the chimney connector.

9.Slip the roof flashing over the chimney and secure to the roof, being careful to keep the pipe centered in the opening. To meet the code, the chimney must extend above the roof at least 3 feet (91.4 cm), and 2 feet (60.9 cm) above any area of the roof, within 10 feet (304.8 cm) of the end of the chimney.

10.Be sure all pieces including outside rain cap, flange, collar and pipe are installed and then place the stove back into position.

11.Install the smoke pipe with the lower (crimped) edge of the pipe inside the smoke collar. Any creosote formed will then run back down into the stove. All connections must be tight and secured with three sheet metal screws equally spaced.

12.Also install an outside air flex pipe to the stove.

13

Page 12 Page 14
Page 13
Image 13
Enviro 2100 Freestanding owner manual Outside AIR
Page 12 Page 14

2100 Freestanding specifications

The Enviro 2100 Freestanding is an exceptional wood stove designed to combine efficiency, style, and functionality. This modern stove is crafted for homeowners seeking an environmentally friendly heating solution without sacrificing aesthetics or performance.

One of the standout features of the Enviro 2100 is its impressive heating capacity. With the ability to effectively heat spaces of up to 2,000 square feet, it provides an ideal solution for large living areas or open floor plans. The efficient heat output ensures that rooms maintain a consistent and comfortable temperature, even during the coldest winter months.

The Enviro 2100 incorporates advanced clean burning technologies that significantly reduce emissions while maximizing heat production. Its innovative design allows for a secondary combustion system that ignites and burns off unburned gases and particulates. This not only minimizes the environmental impact, but also enhances fuel efficiency, giving homeowners more warmth for less wood consumption.

Durability and craftsmanship are also key characteristics of the Enviro 2100. Constructed from high-quality steel and featuring a cast iron door, this stove is built to withstand the demands of daily use. The large firebox is designed for easy loading, accommodating larger logs for longer burn times, thus reducing the frequency of reloading.

Aesthetically, the Enviro 2100 Freestanding stove offers a range of customization options. Buyers can choose between various finishes, including classic black or a more contemporary brushed nickel, allowing them to match the stove with their home décor. Additionally, the large glass viewing window provides an alluring glimpse of the flickering flames, creating a cozy ambiance in any setting.

Safety features are thoughtfully integrated into the design of the Enviro 2100. The stove includes a built-in air wash system that helps keep the glass clean, ensuring a clear view of the fire while contributing to overall safety. Furthermore, the unit is equipped with a heat shield, allowing for closer placement to walls without compromising safety or performance.

In summary, the Enviro 2100 Freestanding is a standout choice for those seeking an efficient and stylish wood heating solution. With its impressive heating capacity, advanced clean burning technologies, durable construction, customizable design, and essential safety features, it is truly a remarkable addition to any home. Whether for functional warmth or aesthetic value, the Enviro 2100 promises to deliver an exceptional experience for years to come.