CASTERS AND WHEELS INSTALLED ONTO CART ASSEMBLY:
When the cart cabinet has been emptied the wheels and casters can be installed. Leave the cart body upside down; this will make installing the wheels and casters easier.
Components Required: |
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
● | ● (2) | Plated caster assemblies | ● Aluminum axle and (2) end caps | |||||||||||||||||
● (2) Stainless steel axle mount | ● (2) | BBQ wheels | ● (14) 1⁄4” x 1⁄2” stainless steel bolts | |||||||||||||||||
● (14) 1⁄4” stainless steel lock washers | ● (14) 1⁄4” stainless steel nuts |
|
| |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Figure 14 | |
| The casters must be installed on the bottom | |
| left side of the cart body. Each caster requires | |
| four (4) bolts, four (4) lock washers, and | |
| four (4) nuts. Put the casters in place (see | |
Figure 13 | Figure 13 & 14) and slide the bolts through | |
the holes in the caster brackets into the | ||
| ||
| holes in the bottom of the cart body. Open | |
| cabinet doors and place a lock washer and a | |
| nut onto each bolt. Using a 1⁄4” socket or nut | |
| driver and a 5/32” Allen key, tighten all the | |
| nuts and bolts. |
The axel mounts must be installed on the right side of the cart body. Each axel mount requires three (3) bolts, three (3) lock washers, and three (3) nuts. Put the axel mounts in place with the holes for the axel closest to the bottom of the cart body (see Figure 13 & 15). Slide the bolts through the holes in the mount into the holes in the side of the cart body. Place a lock washer and a nut onto each bolt. Using a 1⁄4” socket or nut driver and a 5/32” Allen key tighten all the nuts and bolts.
Before the wheels can be installed they must be partially assembled. Press one wheel onto an end of the axel so that approximately 1⁄2” (1 cm) of the axel is out past the wheel. The side with the webbing on it
is to face out. A hammer or mallet may be needed to help put the wheels on the axel. Press an end cap all the way onto the end of the axel with the wheel on it; ensure the wheel is butted up against the end cap (see Figure 16). Slide the axel through the holes in both axel mounts; it may be a tight fit so turn the axel while pressing it through the holes. Press the other wheel, then the end cap, onto the free end of the axel.
8
